From gsosa at snf.stanford.edu Mon Aug 4 16:04:16 2008 From: gsosa at snf.stanford.edu (gsosa at snf.stanford.edu) Date: Mon, 4 Aug 2008 16:04:16 -0700 Subject: Comment bluem SNF 2008-08-04 16:04:15: Update 8/4/08 Message-ID: Checked all wiring inside control box. Tightened up TC wires and tested TC input to controller. Oven is still down and under observation. Do not Use. From gsosa at snf.stanford.edu Wed Aug 13 15:48:05 2008 From: gsosa at snf.stanford.edu (gsosa at snf.stanford.edu) Date: Wed, 13 Aug 2008 15:48:05 -0700 Subject: Comment bluem SNF 2008-08-13 15:48:04: Update 8/13/08 Message-ID: We are goint to replace the thermocouple to see if this resolves the problem. The thermocouple has been ordered and should be here soon. From vilanova at snf.stanford.edu Thu Aug 21 14:03:08 2008 From: vilanova at snf.stanford.edu (vilanova at snf.stanford.edu) Date: Thu, 21 Aug 2008 14:03:08 -0700 Subject: Comment bluem SNF 2008-08-21 14:03:06: Update!! Message-ID: Replaced TC , I Also fixed the power Button , I Still have to calibrate the TC and the system will be down for now, Sorry for the inconvinience. :-( From vilanova at snf.stanford.edu Fri Aug 22 14:24:41 2008 From: vilanova at snf.stanford.edu (vilanova at snf.stanford.edu) Date: Fri, 22 Aug 2008 14:24:41 -0700 Subject: Comment bluem SNF 2008-08-22 14:24:41: Update Message-ID: BLue M Iven still down , after replacing the TC I got a SnSr Sensor error , Acording to the manual I have to calibrate the TC But when I want to do that and get into the Cal1 settings the system doesnt respond SO we have to make sure the TC is the right one and also Call Vendor for more info regarding this Issue. From vilanova at snf.stanford.edu Mon Aug 25 14:40:01 2008 From: vilanova at snf.stanford.edu (vilanova at snf.stanford.edu) Date: Mon, 25 Aug 2008 14:40:01 -0700 Subject: Comment bluem SNF 2008-08-25 14:40:01: Testing System In progress....... Message-ID: The System will be in testing MOde ( program # 2 ) for a couple of days , we have to make sure the TC is working properly or if we get the 555 error, we are recording the system data. From gsosa at snf.stanford.edu Wed Aug 27 16:17:46 2008 From: gsosa at snf.stanford.edu (gsosa at snf.stanford.edu) Date: Wed, 27 Aug 2008 16:17:46 -0700 Subject: Comment bluem SNF 2008-08-27 16:17:44: Update 8/28/08 Message-ID: Running program 2 still in progress. It has been about 32 hours. No problems yet. Oven controlling at 180 degrees. We are also data logging while the program runs it course. From vilanova at snf.stanford.edu Thu Aug 28 15:05:25 2008 From: vilanova at snf.stanford.edu (vilanova at snf.stanford.edu) Date: Thu, 28 Aug 2008 15:05:25 -0700 Subject: Shutdown bluem SNF 2008-07-31 08:08:15: Temp control problem Message-ID: Replaced Thermocouple and ran a couple of Tests ( program # 2, 3 ) everything was normal Temperature has been teady for a coupel of days , NO more sensor or 555 Error at the end of the cycle, please check programs before you use them one of the problems was that someone changed some of the program settings . From vilanova at snf.stanford.edu Thu Aug 28 15:08:05 2008 From: vilanova at snf.stanford.edu (vilanova at snf.stanford.edu) Date: Thu, 28 Aug 2008 15:08:05 -0700 Subject: Problem bluem SNF 2008-06-29 12:54:23: front panel temp. reading 600C Message-ID: Replaced Thermocouple and ran a couple of Tests ( program # 2, 3 ) everything was normal Temperature has been teady for a coupel of days , NO more sensor or 555 Error at the end of the cycle, please check programs before you use them one of the problems was that someone changed some of the program settings . From vilanova at snf.stanford.edu Thu Aug 28 15:08:20 2008 From: vilanova at snf.stanford.edu (vilanova at snf.stanford.edu) Date: Thu, 28 Aug 2008 15:08:20 -0700 Subject: Problem bluem SNF 2008-07-30 17:40:56: defective T/C? Message-ID: Replaced Thermocouple and ran a couple of Tests ( program # 2, 3 ) everything was normal Temperature has been teady for a coupel of days , NO more sensor or 555 Error at the end of the cycle, please check programs before you use them one of the problems was that someone changed some of the program settings .