From mahnaz at snf.stanford.edu  Fri May  2 16:02:09 2003
From: mahnaz at snf.stanford.edu (Mahnaz)
Date: Fri, 02 May 2003 16:02:09 -0700
Subject: DENT
Message-ID: <3EB2F8F1.A82683C3@snf.stanford.edu>


Hello all,

Yesterday 5/1 I did a training on the system and noticed a little
dent/flake on the pressure plate. Please take extra care and make sure
for now the force do not exceed 1500N.
The rule is that with Glass pressure plate the force should not exceed
over 2000 N
and if higher force required we need to use the  steel  pressure plate
and Mike and I need to be notified.
Stay safe over the weekend

mahnaz



From yy7343 at hotmail.com  Fri May  2 17:28:54 2003
From: yy7343 at hotmail.com (Yahong Yao)
Date: Fri, 02 May 2003 17:28:54 -0700
Subject: DENT
Message-ID: <Law12-F20bLD95rFcdu0001f3a0@hotmail.com>

Hi Mahnaz,

I remember that the program doesn't allow us to apply pressure higher than 
1340N.  Maybe a wrong stack thickness will cause some damage.

Yahong





>From: Mahnaz <mahnaz at snf.stanford.edu>
>To: evbond at snf.stanford.edu
>Subject: DENT
>Date: Fri, 02 May 2003 16:02:09 -0700
>
>
>Hello all,
>
>Yesterday 5/1 I did a training on the system and noticed a little
>dent/flake on the pressure plate. Please take extra care and make sure
>for now the force do not exceed 1500N.
>The rule is that with Glass pressure plate the force should not exceed
>over 2000 N
>and if higher force required we need to use the  steel  pressure plate
>and Mike and I need to be notified.
>Stay safe over the weekend
>
>mahnaz
>


_________________________________________________________________
STOP MORE SPAM with the new MSN 8 and get 2 months FREE*  
http://join.msn.com/?page=features/junkmail



From yy7343 at hotmail.com  Sat May  3 09:44:11 2003
From: yy7343 at hotmail.com (Yahong Yao)
Date: Sat, 03 May 2003 09:44:11 -0700
Subject: EVbonder Max force 3340N
Message-ID: <Law12-F118X3melfSud0001c311@hotmail.com>

Hi All,

In my previous email, I mentioned the max force the tool allowed us to apply 
was 1340N.  It should be 3340N!  Just checked the program.  Sorry for the 
mistake.

Yahong




>From: Mahnaz <mahnaz at snf.stanford.edu>
>To: evbond at snf.stanford.edu
>Subject: DENT
>Date: Fri, 02 May 2003 16:02:09 -0700
>
>
>Hello all,
>
>Yesterday 5/1 I did a training on the system and noticed a little
>dent/flake on the pressure plate. Please take extra care and make sure
>for now the force do not exceed 1500N.
>The rule is that with Glass pressure plate the force should not exceed
>over 2000 N
>and if higher force required we need to use the  steel  pressure plate
>and Mike and I need to be notified.
>Stay safe over the weekend
>
>mahnaz
>


_________________________________________________________________
Add photos to your messages with MSN 8. Get 2 months FREE*.  
http://join.msn.com/?page=features/featuredemail



From mahnaz at snf.stanford.edu  Mon May  5 15:14:28 2003
From: mahnaz at snf.stanford.edu (Mahnaz)
Date: Mon, 05 May 2003 15:14:28 -0700
Subject: EV  presentation
Message-ID: <3EB6E244.DF3A8027@snf.stanford.edu>


Hello all,

I like to let you know that Chad Brubaker an staff engineer from
Electronic Vision will be here at Stanford on 5/8.  We will do bond
training in the morning around 9:30 am. If you need bond training or
recently have been trained on the equipment; I strongly suggest to
attend the session. The afternoon session is for EV aligner training and
we will start about 2 Pm with topside , bottom site and anodic
alignment.

Or just come with  your questions and suggestions.
Hope to see you
Mahnaz



From mahnaz at snf.stanford.edu  Tue May 13 11:14:11 2003
From: mahnaz at snf.stanford.edu (Mahnaz)
Date: Tue, 13 May 2003 11:14:11 -0700
Subject: Pressure
Message-ID: <3EC135F3.1CFFC2B@snf.stanford.edu>


Hello all,
The condition of the pressure plate is getting worse, the part is on
order it will take another week or two so till then YOU MAY NOT USE ANY
FORCE GREATER THAN 1500N AT THIS TIME.

mahnaz