From faridz at snf.stanford.edu Wed Jan 6 11:23:44 2010 From: faridz at snf.stanford.edu (faridz at snf.stanford.edu) Date: Wed, 6 Jan 2010 11:23:44 -0800 Subject: Comment headway2 SNF 2010-01-06 11:23:43: hot plate issues Message-ID: New hot plate have calibration problem. Mario installing old hot plate back. From jwc at snf.stanford.edu Tue Jan 12 11:54:12 2010 From: jwc at snf.stanford.edu (jwc at snf.stanford.edu) Date: Tue, 12 Jan 2010 11:54:12 -0800 Subject: Comment headway2 SNF 2010-01-06 11:23:43: hot plate issues Message-ID: From kimsangb at snf.stanford.edu Fri Jan 22 10:27:53 2010 From: kimsangb at snf.stanford.edu (kimsangb at snf.stanford.edu) Date: Fri, 22 Jan 2010 10:27:53 -0800 Subject: Comment headway2 SNF 2010-01-22 10:27:53: headway2 dirty Message-ID: When I came in to use headway2, it was quite dirty with a lot of red resists mark. Please clean headway2 and the surface, if you spill some resists. From fanpy at snf.stanford.edu Tue Jan 26 00:20:10 2010 From: fanpy at snf.stanford.edu (fanpy at snf.stanford.edu) Date: Tue, 26 Jan 2010 00:20:10 -0800 Subject: Problem headway2 SNF 2010-01-26 00:20:09: spins without chuck Message-ID: need to check vacuum From fanpy at snf.stanford.edu Tue Jan 26 00:22:57 2010 From: fanpy at snf.stanford.edu (fanpy at snf.stanford.edu) Date: Tue, 26 Jan 2010 00:22:57 -0800 Subject: Comment headway2 SNF 2010-01-26 00:22:57: leftover resist Message-ID: there is a small container with leftover resist in it when previous user came on the tool. I sealed it in a zip bag in case the beaker belongs to someone. From vilanova at snf.stanford.edu Tue Jan 26 07:47:20 2010 From: vilanova at snf.stanford.edu (vilanova at snf.stanford.edu) Date: Tue, 26 Jan 2010 07:47:20 -0800 Subject: Comment headway2 SNF 2010-01-22 10:27:53: headway2 dirty Message-ID: cleaned From vilanova at snf.stanford.edu Tue Jan 26 07:48:08 2010 From: vilanova at snf.stanford.edu (vilanova at snf.stanford.edu) Date: Tue, 26 Jan 2010 07:48:08 -0800 Subject: Problem headway2 SNF 2010-01-26 00:20:09: spins without chuck Message-ID: there was a lot of resist residues all over the spindle , Checked vacuum and cleaned spindle tested , ok to use. From mahnaz at stanford.edu Wed Jan 27 10:46:30 2010 From: mahnaz at stanford.edu (Mahnaz Mansourpour) Date: Wed, 27 Jan 2010 10:46:30 -0800 Subject: Missing 6" chuck Message-ID: <4B608A06.5050202@stanford.edu> Hello all, We are missing the 6" chuck about a week and half. The hope that will come back is diminishing for us . Mario has looked for it with no luck. we have few labmembers with square substrate that relay on that chuck so please if you have seen it or you have taken it by mistake please bring it back. Help a labmember in need O:-) mahnaz From vilanova at snf.stanford.edu Thu Jan 28 07:33:22 2010 From: vilanova at snf.stanford.edu (vilanova at snf.stanford.edu) Date: Thu, 28 Jan 2010 07:33:22 -0800 Subject: Shutdown headway2 SNF 2010-01-28 07:33:21: preventive maintenance in progress.... Message-ID: From vilanova at snf.stanford.edu Thu Jan 28 10:28:15 2010 From: vilanova at snf.stanford.edu (vilanova at snf.stanford.edu) Date: Thu, 28 Jan 2010 10:28:15 -0800 Subject: Shutdown headway2 SNF 2010-01-28 07:33:21: preventive maintenance in progress.... Message-ID: preventive maintenance completed , system has been cleaned and tested( cleaned hoses spindle fittings catch cup , bench , soleonid, tested ok , good to use. From vilanova at snf.stanford.edu Thu Jan 28 10:28:25 2010 From: vilanova at snf.stanford.edu (vilanova at snf.stanford.edu) Date: Thu, 28 Jan 2010 10:28:25 -0800 Subject: Comment headway2 SNF 2010-01-26 00:22:57: leftover resist Message-ID: preventive maintenance completed , system has been cleaned and tested( cleaned hoses spindle fittings catch cup , bench , soleonid, tested ok , good to use. From vilanova at snf.stanford.edu Fri Jan 29 08:59:28 2010 From: vilanova at snf.stanford.edu (vilanova at snf.stanford.edu) Date: Fri, 29 Jan 2010 08:59:28 -0800 Subject: Comment headway2 SNF 2010-01-29 08:59:11: White Insert Spare Oring Message-ID: I left A bag With SOme Extra White Insert Orings, this is in case the Ones that the chucks have are to dirty , to replace it just remove the old one and thow it away clean the White insert with acetone put the new Oring , This will make the chuck get better vacuum and also will keep your sample from getting Dirty particles. From klharris at snf.stanford.edu Fri Jan 29 20:48:34 2010 From: klharris at snf.stanford.edu (klharris at snf.stanford.edu) Date: Fri, 29 Jan 2010 20:48:34 -0800 Subject: Problem headway2 SNF 2010-01-29 20:48:34: spins without chuck Message-ID: i tried cleaning out the spindle with a bit of IPA soaked wipe without any luck. From shott at snf.stanford.edu Sat Jan 30 07:01:19 2010 From: shott at snf.stanford.edu (shott at snf.stanford.edu) Date: Sat, 30 Jan 2010 07:01:19 -0800 Subject: Problem headway2 SNF 2010-01-29 20:48:34: spins without chuck Message-ID: With a bit of welding rod, I was able to "rod out" the spindle shaft. It now requires vacuum to spin. Blockage did not seem particularly severe .... just a light blockage up near the top of the shaft. Likely Mario and Gary will do a more comprehensive job of fixing this on Monday, but this should get us through the weekend. John