From jperez at snf.stanford.edu Mon Apr 1 02:40:34 2002 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Apr 1, 2002 2:40:34 PM Subject: Problem innotec 2002-04-01 14:40:33: MDC Abort after pressing the STOP button Message-ID: Starting the deposition by pressing the red stop button, the alarm sounded. I don't know why it aborted. The only thing I can think of, is that the red stop button was pressed too long. From jperez at snf.stanford.edu Mon Apr 1 03:35:01 2002 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Apr 1, 2002 3:35:01 PM Subject: Problem innotec 2002-04-01 15:35:00: Innotec back up,Maurice helped us out of the MDC abort Message-ID: From jperez at snf.stanford.edu Mon Apr 1 03:36:34 2002 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Apr 1, 2002 3:36:34 PM Subject: Problem innotec 2002-04-01 14:40:33: MDC Abort after pressing the STOP button Message-ID: Maurice helped getting us out of the MDC abort mode From jperez at snf.stanford.edu Mon Apr 1 03:36:56 2002 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Apr 1, 2002 3:36:56 PM Subject: Problem innotec 2002-04-01 15:35:00: Innotec back up,Maurice helped us out of the MDC abort Message-ID: From jperez at snf.stanford.edu Mon Apr 15 07:53:29 2002 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Apr 15, 2002 7:53:29 AM Subject: Problem innotec 2002-04-15 07:53:28: Cr source power at zero percent, caustion! Message-ID: The chromium sourse has straight side walls, you need to start off very slow and then cut back on the power. Ordering standard size. From jhaydon at snf.stanford.edu Tue Apr 16 09:35:01 2002 From: jhaydon at snf.stanford.edu (jhaydon at snf.stanford.edu) Date: Apr 16, 2002 9:35:01 AM Subject: Shutdown innotec 2002-04-16 09:35:00: shut down for cryo regen Message-ID: From jhaydon at snf.stanford.edu Tue Apr 16 04:09:37 2002 From: jhaydon at snf.stanford.edu (jhaydon at snf.stanford.edu) Date: Apr 16, 2002 4:09:37 PM Subject: Shutdown innotec 2002-04-16 09:35:00: shut down for cryo regen Message-ID: regen completed ok to use From cmfaulkn at snf.stanford.edu Mon Apr 22 09:47:49 2002 From: cmfaulkn at snf.stanford.edu (cmfaulkn at snf.stanford.edu) Date: Apr 22, 2002 9:47:49 PM Subject: Problem innotec 2002-04-22 21:47:49: Al target removed Message-ID: The ebeam required about 2% power to turn on and then the Al target wouldn't glow. After venting, it was observed that the Al was heavily oxidized (or had some other whitish crud on it). Target cleaned, but NOT put back in the crucible. From jperez at snf.stanford.edu Fri Apr 26 04:02:20 2002 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Apr 26, 2002 4:02:20 PM Subject: Problem innotec 2002-04-22 21:47:49: Al target removed Message-ID: Replaced Aluminum source. From jperez at snf.stanford.edu Fri Apr 26 04:03:43 2002 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Apr 26, 2002 4:03:43 PM Subject: Problem innotec 2002-04-15 07:53:28: Cr source power at zero percent, caustion! Message-ID: Replaced odd size Cr source with new truncated cone source. From jperez at snf.stanford.edu Fri Apr 26 04:14:02 2002 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Apr 26, 2002 4:14:02 PM Subject: Problem innotec 2002-04-26 16:14:01: Second time the belljar fell from about 3-4 inches from closing. Message-ID: The inner shield is getting stuck when lowered and meets the ion gun bracket. It drops so hard that the wafer holders with one pin holding on to the planetarium.drop to the bottom. From jhaydon at snf.stanford.edu Mon Apr 29 02:54:29 2002 From: jhaydon at snf.stanford.edu (jhaydon at snf.stanford.edu) Date: Apr 29, 2002 2:54:29 PM Subject: Problem innotec 2002-04-26 16:14:01: Second time the belljar fell from about 3-4 inches from closing. Message-ID: braket holding ion gun has been modified the bell jar should not get hung up again