From jperez at snf.stanford.edu Mon Feb 4 08:12:20 2008 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Mon, 4 Feb 2008 08:12:20 -0800 Subject: Comment innotec SNF 2008-01-26 19:56:16: F2 (toggle switch) jam, Cr source in poor shape Message-ID: Replaced Cr starter source From dtschoen at snf.stanford.edu Mon Feb 11 17:59:50 2008 From: dtschoen at snf.stanford.edu (dtschoen at snf.stanford.edu) Date: Mon, 11 Feb 2008 17:59:50 -0800 Subject: Comment innotec SNF 2008-02-11 17:59:49: Last Shutter Message-ID: I used the last new shutter today. There are no more new shutters. From dtschoen at snf.stanford.edu Mon Feb 11 18:00:28 2008 From: dtschoen at snf.stanford.edu (dtschoen at snf.stanford.edu) Date: Mon, 11 Feb 2008 18:00:28 -0800 Subject: Comment innotec SNF 2008-02-11 18:00:27: Removed Peeling Dummy Message-ID: One of the dummy wafers was badlly peeling so I removed it. I have nothing to replace it with, so the system is down 1 dummy wafer. From jperez at snf.stanford.edu Tue Feb 12 11:02:09 2008 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Tue, 12 Feb 2008 11:02:09 -0800 Subject: Comment innotec SNF 2008-02-11 18:00:27: Removed Peeling Dummy Message-ID: Added dummies to the box From jperez at snf.stanford.edu Tue Feb 12 11:03:32 2008 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Tue, 12 Feb 2008 11:03:32 -0800 Subject: Comment innotec SNF 2008-02-11 17:59:49: Last Shutter Message-ID: Still was one more clean shutter under table. Added 4 more shutters that came back from clean. From yeh at snf.stanford.edu Tue Feb 12 13:02:37 2008 From: yeh at snf.stanford.edu (yeh at snf.stanford.edu) Date: Tue, 12 Feb 2008 13:02:37 -0800 Subject: Comment innotec SNF 2008-02-12 13:02:36: 300A Al evap on 2/8 Message-ID: got <200A instead of the target 300A. From gibby at snf.stanford.edu Thu Feb 14 17:08:28 2008 From: gibby at snf.stanford.edu (gibby at snf.stanford.edu) Date: Thu, 14 Feb 2008 17:08:28 -0800 Subject: Problem innotec SNF 2008-02-14 17:08:27: Film will not advance Message-ID: Film under polatized glass window will not advance. From zhangy at snf.stanford.edu Thu Feb 14 21:08:12 2008 From: zhangy at snf.stanford.edu (zhangy at snf.stanford.edu) Date: Thu, 14 Feb 2008 21:08:12 -0800 Subject: Problem innotec SNF 2008-02-14 21:08:12: vent light problem Message-ID: After the chamber was vented for more than 10 minutes, the vent light was still not on. However, the chamber did look vented. Eric helped to check the sensor at the back , and it worked after he adjusted the vent light sensor. From jperez at snf.stanford.edu Fri Feb 15 14:59:27 2008 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Fri, 15 Feb 2008 14:59:27 -0800 Subject: Problem innotec SNF 2008-02-14 21:08:12: vent light problem Message-ID: Eric must of done a good job because I had no problems today venting twice. From jperez at snf.stanford.edu Fri Feb 15 15:00:22 2008 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Fri, 15 Feb 2008 15:00:22 -0800 Subject: Problem innotec SNF 2008-02-14 17:08:27: Film will not advance Message-ID: Jim Haydon changed the roll of film. The film was all used up. From jhpark9 at snf.stanford.edu Sat Feb 16 22:40:09 2008 From: jhpark9 at snf.stanford.edu (jhpark9 at snf.stanford.edu) Date: Sat, 16 Feb 2008 22:40:09 -0800 Subject: Problem innotec SNF 2008-02-16 22:40:08: gray wire(back side) conneted to top of chamber. Message-ID: Please check the wire. It's a little bit peeled off. While operating, there was no problem. From jperez at snf.stanford.edu Tue Feb 19 13:25:06 2008 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Tue, 19 Feb 2008 13:25:06 -0800 Subject: Problem innotec SNF 2008-02-16 22:40:08: gray wire(back side) conneted to top of chamber. Message-ID: Elmer taped the area that has a cut in the cord that connects to the motor that rotates the planetary. Jim Haydon will replace cord when he comes back. From dejia at snf.stanford.edu Wed Feb 20 00:06:13 2008 From: dejia at snf.stanford.edu (dejia at snf.stanford.edu) Date: Wed, 20 Feb 2008 00:06:13 -0800 Subject: Problem innotec SNF 2008-02-20 00:06:12: pt source fell Message-ID: Pt source fell down the small hole next to the crucible. I can see it but i cannot bring it up from the hole. From emyers at snf.stanford.edu Thu Feb 21 10:07:56 2008 From: emyers at snf.stanford.edu (emyers at snf.stanford.edu) Date: Thu, 21 Feb 2008 10:07:56 -0800 Subject: Problem innotec SNF 2008-02-20 00:06:12: pt source fell Message-ID: Worked with Jeannie to recover Pt source. From king at snf.stanford.edu Fri Feb 22 00:15:34 2008 From: king at snf.stanford.edu (king at snf.stanford.edu) Date: Fri, 22 Feb 2008 00:15:34 -0800 Subject: Problem innotec SNF 2008-02-22 00:15:33: Hoist makes a loud screeching noise Message-ID: It needs to be greased and no one seems to have written it up Thanks in advance. From nppatil at snf.stanford.edu Sat Feb 23 12:43:31 2008 From: nppatil at snf.stanford.edu (nppatil at snf.stanford.edu) Date: Sat, 23 Feb 2008 12:43:31 -0800 Subject: Problem innotec SNF 2008-02-23 12:43:30: Roughing Pump Message-ID: Pump does not work. From nppatil at snf.stanford.edu Sat Feb 23 14:20:22 2008 From: nppatil at snf.stanford.edu (nppatil at snf.stanford.edu) Date: Sat, 23 Feb 2008 14:20:22 -0800 Subject: Shutdown innotec SNF 2008-02-23 14:20:21: Roughing pump Message-ID: John Shott reset the tripped circuit breaker for the pump in the panel behind the Innotec. However, foreline pressure is high (400 mTorr). Even after 30 mins of pumping, roughing pump does not reach the crossover pressure (150 mTorr). I turned off the roughing pump and shutdown the system. From jhaydon at snf.stanford.edu Tue Feb 26 06:56:14 2008 From: jhaydon at snf.stanford.edu (jhaydon at snf.stanford.edu) Date: Tue, 26 Feb 2008 06:56:14 -0800 Subject: Shutdown innotec SNF 2008-02-23 14:20:21: Roughing pump Message-ID: roughing pump[ back on From jhaydon at snf.stanford.edu Tue Feb 26 06:56:37 2008 From: jhaydon at snf.stanford.edu (jhaydon at snf.stanford.edu) Date: Tue, 26 Feb 2008 06:56:37 -0800 Subject: Problem innotec SNF 2008-02-23 12:43:30: Roughing Pump Message-ID: pump working now From jhaydon at snf.stanford.edu Tue Feb 26 06:57:06 2008 From: jhaydon at snf.stanford.edu (jhaydon at snf.stanford.edu) Date: Tue, 26 Feb 2008 06:57:06 -0800 Subject: Problem innotec SNF 2008-02-22 00:15:33: Hoist makes a loud screeching noise Message-ID: hoist noise has been reduced