From jperez at snf.stanford.edu Mon Jun 1 06:52:26 2009 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Mon, 1 Jun 2009 06:52:26 -0700 Subject: Problem innotec SNF 2009-05-30 17:36:36: pump abnormally loud, chamber peeling Message-ID: We will go down for a PM (chamber clean) July 7th. We'll vacuum until then. I will monitor the condition. From jperez at snf.stanford.edu Mon Jun 1 06:54:32 2009 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Mon, 1 Jun 2009 06:54:32 -0700 Subject: Comment innotec SNF 2009-05-15 11:12:39: Spare shutter, wrong hole Message-ID: Removed shutter. Jim Haydon will drill a hole on the left side. From panjun at snf.stanford.edu Mon Jun 1 15:14:35 2009 From: panjun at snf.stanford.edu (panjun at snf.stanford.edu) Date: Mon, 1 Jun 2009 15:14:35 -0700 Subject: Comment innotec SNF 2009-06-01 15:14:35: Cr source has a deep hole Message-ID: the Cr souce has a deep hole before i use it. The hole is almost through to the bottom but not yet. So i think it's still ok to use. I filled some pellets in the hole. From jperez at snf.stanford.edu Tue Jun 2 11:03:25 2009 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Tue, 2 Jun 2009 11:03:25 -0700 Subject: Comment innotec SNF 2009-06-01 15:14:35: Cr source has a deep hole Message-ID: Thanks for the information. I'll check it today and you made the right decision to add pellets in the hole and continue using the Cr source. From jperez at snf.stanford.edu Tue Jun 2 11:04:42 2009 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Tue, 2 Jun 2009 11:04:42 -0700 Subject: Problem innotec SNF 2009-05-30 12:59:17: Au source damaged Message-ID: Did not see a big hole or that the Au source was damaged. From yoonyoung at snf.stanford.edu Thu Jun 4 10:07:09 2009 From: yoonyoung at snf.stanford.edu (yoonyoung at snf.stanford.edu) Date: Thu, 4 Jun 2009 10:07:09 -0700 Subject: Problem innotec SNF 2009-06-04 10:07:09: Gold Pallets Message-ID: There is no gold pallets and the gold source has a pretty big hole in the middle! From maurice at snf.stanford.edu Thu Jun 4 17:05:06 2009 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Thu, 4 Jun 2009 17:05:06 -0700 Subject: Comment innotec SNF 2009-06-04 17:05:06: replaced Au source Message-ID: From jperez at snf.stanford.edu Fri Jun 5 07:02:07 2009 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Fri, 5 Jun 2009 07:02:07 -0700 Subject: Problem innotec SNF 2009-06-04 10:07:09: Gold Pallets Message-ID: Refilled Au baggy, starter source looks good From jperez at snf.stanford.edu Fri Jun 5 07:03:12 2009 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Fri, 5 Jun 2009 07:03:12 -0700 Subject: Comment innotec SNF 2009-06-04 17:05:06: replaced Au source Message-ID: Filled Au baggy with pellets. From xutian at snf.stanford.edu Sun Jun 7 09:41:43 2009 From: xutian at snf.stanford.edu (xutian at snf.stanford.edu) Date: Sun, 7 Jun 2009 09:41:43 -0700 Subject: Problem innotec SNF 2009-06-07 09:41:42: Pt pellets need replenishment Message-ID: From jperez at snf.stanford.edu Mon Jun 8 08:02:43 2009 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Mon, 8 Jun 2009 08:02:43 -0700 Subject: Problem innotec SNF 2009-06-07 09:41:42: Pt pellets need replenishment Message-ID: Added Pt Pellets to the baggy. From sipark at snf.stanford.edu Sat Jun 13 01:18:14 2009 From: sipark at snf.stanford.edu (sipark at snf.stanford.edu) Date: Sat, 13 Jun 2009 01:18:14 -0700 Subject: Problem innotec SNF 2009-06-13 01:18:13: Interlock problem Message-ID: The system is interlocked and I couldn't proceed the next step. (It seemed that previous user left the system without taking any action.) From ghyrn at snf.stanford.edu Sat Jun 13 07:30:38 2009 From: ghyrn at snf.stanford.edu (ghyrn at snf.stanford.edu) Date: Sat, 13 Jun 2009 07:30:38 -0700 Subject: Comment innotec SNF 2009-06-13 07:30:37: Interlock Problem Message-ID: I haven't noticed anything unusual yet. Pump down proceeding normally. From ghyrn at snf.stanford.edu Sat Jun 13 09:32:09 2009 From: ghyrn at snf.stanford.edu (ghyrn at snf.stanford.edu) Date: Sat, 13 Jun 2009 09:32:09 -0700 Subject: Problem innotec SNF 2009-06-13 09:32:09: Interlock Problem Message-ID: So I now am having the same problem the last user experienced. The Interlock WFS1 message was flashing even though I enabled the machine. Everything proceeded normally until I go to turn on the Source 1. Nothing happens. I don't know how to reset this. Tried going back through the procedure a couple times to no avail. From shott at snf.stanford.edu Sat Jun 13 11:30:18 2009 From: shott at snf.stanford.edu (shott at snf.stanford.edu) Date: Sat, 13 Jun 2009 11:30:18 -0700 Subject: Problem innotec SNF 2009-06-13 01:18:13: Interlock problem Message-ID: I found that water in the reservior in the Neslab chiller was low. Refilling it seemed to be just enough to cause the interlock problem go away. However, the return line to the chiller is collapsed due to suction for about the first 6-8 feet of the return line from the chiller down trhough the floor. This should be replaced ASAP with equivalent spiral wire line to prevent collapse. Thanks, John From shott at snf.stanford.edu Sat Jun 13 11:30:26 2009 From: shott at snf.stanford.edu (shott at snf.stanford.edu) Date: Sat, 13 Jun 2009 11:30:26 -0700 Subject: Comment innotec SNF 2009-06-13 07:30:37: Interlock Problem Message-ID: I found that water in the reservior in the Neslab chiller was low. Refilling it seemed to be just enough to cause the interlock problem go away. However, the return line to the chiller is collapsed due to suction for about the first 6-8 feet of the return line from the chiller down trhough the floor. This should be replaced ASAP with equivalent spiral wire line to prevent collapse. Thanks, John From shott at snf.stanford.edu Sat Jun 13 11:30:34 2009 From: shott at snf.stanford.edu (shott at snf.stanford.edu) Date: Sat, 13 Jun 2009 11:30:34 -0700 Subject: Problem innotec SNF 2009-06-13 09:32:09: Interlock Problem Message-ID: I found that water in the reservior in the Neslab chiller was low. Refilling it seemed to be just enough to cause the interlock problem go away. However, the return line to the chiller is collapsed due to suction for about the first 6-8 feet of the return line from the chiller down trhough the floor. This should be replaced ASAP with equivalent spiral wire line to prevent collapse. Thanks, John From duygu at snf.stanford.edu Sat Jun 13 16:46:38 2009 From: duygu at snf.stanford.edu (duygu at snf.stanford.edu) Date: Sat, 13 Jun 2009 16:46:38 -0700 Subject: Problem innotec SNF 2009-06-13 16:46:38: WFS1 problem again Message-ID: The Interlock WFS1 problem again.The Interlock WFS1 message was flashing. I did Ti evaporation, it went fine. When I moved to second metal Al, I saw the beam at the begining then it went off. Water light on Source 1 went off. I am unloading my sample. From dongrip at snf.stanford.edu Sun Jun 14 03:26:45 2009 From: dongrip at snf.stanford.edu (dongrip at snf.stanford.edu) Date: Sun, 14 Jun 2009 03:26:45 -0700 Subject: Comment innotec SNF 2009-06-14 03:26:44: WFS1 problem Message-ID: I did three runs including dummy run to check WFS1 problem, and all my runs were okay. No problem was observed during my runs, but WFS1 issue may occur again... From mtang at snf.stanford.edu Mon Jun 15 09:24:43 2009 From: mtang at snf.stanford.edu (mtang at snf.stanford.edu) Date: Mon, 15 Jun 2009 09:24:43 -0700 Subject: Problem innotec SNF 2009-06-13 16:46:38: WFS1 problem again Message-ID: See John's message clearing the problem 6/13/09. From jperez at snf.stanford.edu Tue Jun 16 07:07:50 2009 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Tue, 16 Jun 2009 07:07:50 -0700 Subject: Comment innotec SNF 2009-06-14 03:26:44: WFS1 problem Message-ID: Filled Chiller with water in basement for Innotec. From jimkruger at snf.stanford.edu Tue Jun 16 17:17:47 2009 From: jimkruger at snf.stanford.edu (jimkruger at snf.stanford.edu) Date: Tue, 16 Jun 2009 17:17:47 -0700 Subject: Comment innotec SNF 2009-06-16 17:17:47: Be careful on lowering BellJar Message-ID: One water hose is tending to kink and curl under the belljar as it lowers. Stop, straighted the hose, then continue lowering. Be sure to lower the last 2 inches or so in one motion or the jar may not seal. From mtang at snf.stanford.edu Mon Jun 22 09:23:24 2009 From: mtang at snf.stanford.edu (mtang at snf.stanford.edu) Date: Mon, 22 Jun 2009 09:23:24 -0700 Subject: Problem innotec SNF 2009-05-21 06:33:17: unstable voltage Message-ID: No recent reports. Please report if this is observed. Watch the vacuum when this occurs -- suspicion is a small burst of pressure. From mtang at snf.stanford.edu Mon Jun 22 09:24:25 2009 From: mtang at snf.stanford.edu (mtang at snf.stanford.edu) Date: Mon, 22 Jun 2009 09:24:25 -0700 Subject: Problem innotec SNF 2009-05-08 12:05:22: High Vac went off during deposition Message-ID: No recent reports. Please report if this is observed. Watch the vacuum when this occurs -- suspicion is a small burst of pressure. From mtang at snf.stanford.edu Mon Jun 22 09:24:29 2009 From: mtang at snf.stanford.edu (mtang at snf.stanford.edu) Date: Mon, 22 Jun 2009 09:24:29 -0700 Subject: Problem innotec SNF 2009-05-08 15:49:45: drops in high voltage power Message-ID: No recent reports. Please report if this is observed. Watch the vacuum when this occurs -- suspicion is a small burst of pressure. From xinyubao at snf.stanford.edu Sun Jun 28 02:04:03 2009 From: xinyubao at snf.stanford.edu (xinyubao at snf.stanford.edu) Date: Sun, 28 Jun 2009 02:04:03 -0700 Subject: Problem innotec SNF 2009-06-28 02:04:03: sweep power supply went off Message-ID: sweep power supply went off when the beam power reached 3.0% for Ni, during the beam positioning From jperez at snf.stanford.edu Mon Jun 29 06:46:10 2009 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Mon, 29 Jun 2009 06:46:10 -0700 Subject: Problem innotec SNF 2009-06-28 02:04:03: sweep power supply went off Message-ID: There is a note attached to Innotec to wait two minutes once the power supply is turned on before raising power. From xinyubao at snf.stanford.edu Mon Jun 29 21:22:49 2009 From: xinyubao at snf.stanford.edu (xinyubao at snf.stanford.edu) Date: Mon, 29 Jun 2009 21:22:49 -0700 Subject: Problem innotec SNF 2009-06-29 21:22:48: cannot lift the bell jar Message-ID: still cannot open it after the ATM light was on for more than 10 min. From gdiankov at snf.stanford.edu Tue Jun 30 00:15:52 2009 From: gdiankov at snf.stanford.edu (gdiankov at snf.stanford.edu) Date: Tue, 30 Jun 2009 00:15:52 -0700 Subject: Shutdown innotec SNF 2009-06-30 00:15:52: Bell Jar doesn't open Message-ID: From jhaydon at snf.stanford.edu Tue Jun 30 11:35:46 2009 From: jhaydon at snf.stanford.edu (jhaydon at snf.stanford.edu) Date: Tue, 30 Jun 2009 11:35:46 -0700 Subject: Shutdown innotec SNF 2009-06-30 00:15:52: Bell Jar doesn't open Message-ID: replaced broken rollpin in lift and reset close sensor From jhaydon at snf.stanford.edu Tue Jun 30 11:36:28 2009 From: jhaydon at snf.stanford.edu (jhaydon at snf.stanford.edu) Date: Tue, 30 Jun 2009 11:36:28 -0700 Subject: Problem innotec SNF 2009-06-29 21:22:48: cannot lift the bell jar Message-ID: replaced rollpin in lift and reset close sensor