From maurice at snf.stanford.edu Wed Jul 7 16:03:48 2010 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Wed, 7 Jul 2010 16:03:48 -0700 Subject: Comment innotec SNF 2010-07-07 16:03:47: added 10 Au pellets Message-ID: added 10 Au pellets From jackson at snf.stanford.edu Wed Jul 7 20:46:25 2010 From: jackson at snf.stanford.edu (jackson at snf.stanford.edu) Date: Wed, 7 Jul 2010 20:46:25 -0700 Subject: Problem innotec SNF 2010-07-07 20:46:25: high voltage does not come on Message-ID: tried multiple time, but high voltage will not come on...stays at 0.01 From jhaydon at snf.stanford.edu Thu Jul 8 08:18:44 2010 From: jhaydon at snf.stanford.edu (jhaydon at snf.stanford.edu) Date: Thu, 8 Jul 2010 08:18:44 -0700 Subject: Problem innotec SNF 2010-07-07 20:46:25: high voltage does not come on Message-ID: replcaced E-gun From jimkruger at snf.stanford.edu Thu Jul 8 08:49:28 2010 From: jimkruger at snf.stanford.edu (jimkruger at snf.stanford.edu) Date: Thu, 8 Jul 2010 08:49:28 -0700 Subject: Problem innotec SNF 2010-07-08 08:49:28: no Au pellets left Message-ID: I used the last 2. From jimkruger at snf.stanford.edu Thu Jul 8 08:52:19 2010 From: jimkruger at snf.stanford.edu (jimkruger at snf.stanford.edu) Date: Thu, 8 Jul 2010 08:52:19 -0700 Subject: Problem innotec SNF 2010-07-08 08:52:18: Pockets no being cleaned enough Message-ID: I found major build-up on C5=Au pocket and found "pocket" residue bonded to the Cu source. Tried to clean up both of them. Cleaned C4 for Cu. From jimkruger at snf.stanford.edu Thu Jul 8 10:16:53 2010 From: jimkruger at snf.stanford.edu (jimkruger at snf.stanford.edu) Date: Thu, 8 Jul 2010 10:16:53 -0700 Subject: Comment innotec SNF 2010-07-08 10:16:53: New gun "flickers", go slow Message-ID: The new gun seems to need conditioning. It flashes "cutback" and the beam flickers but never cut out for me. It seems to be OK after running a while at a given % pwr, but flickers again as the power is raised. I used 9% maximum. Go slow to higher powers. jimKruger From maurice at snf.stanford.edu Thu Jul 8 10:42:40 2010 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Thu, 8 Jul 2010 10:42:40 -0700 Subject: Comment innotec SNF 2010-07-08 10:42:40: added another 10 Au pelleta Message-ID: Added another 10 pellets to bag. (Just added 10 yesterday) From jhaydon at snf.stanford.edu Fri Jul 9 08:04:35 2010 From: jhaydon at snf.stanford.edu (jhaydon at snf.stanford.edu) Date: Fri, 9 Jul 2010 08:04:35 -0700 Subject: Problem innotec SNF 2010-07-08 08:49:28: no Au pellets left Message-ID: Maurice add some more From svo at snf.stanford.edu Sun Jul 11 10:06:39 2010 From: svo at snf.stanford.edu (svo at snf.stanford.edu) Date: Sun, 11 Jul 2010 10:06:39 -0700 Subject: Comment innotec SNF 2010-07-11 10:06:38: system resetted Message-ID: i followed normal procedures, but when it came to turning on the interlock, then turning on the main power, the system flickered and re-setted... the main power was off and is now on again. i am able to vent but not hit 'pump only.' From svo at snf.stanford.edu Sun Jul 11 10:14:58 2010 From: svo at snf.stanford.edu (svo at snf.stanford.edu) Date: Sun, 11 Jul 2010 10:14:58 -0700 Subject: Problem innotec SNF 2010-07-11 10:14:58: can't pump down Message-ID: now i cannot pump down and system warming to rm temp From svo at snf.stanford.edu Sun Jul 11 10:16:38 2010 From: svo at snf.stanford.edu (svo at snf.stanford.edu) Date: Sun, 11 Jul 2010 10:16:38 -0700 Subject: Shutdown innotec SNF 2010-07-11 10:16:38: can't pump down... Message-ID: From mtang at snf.stanford.edu Sun Jul 11 21:03:33 2010 From: mtang at snf.stanford.edu (mtang at snf.stanford.edu) Date: Sun, 11 Jul 2010 21:03:33 -0700 Subject: Shutdown innotec SNF 2010-07-11 10:16:38: can't pump down... Message-ID: Taking out of shutdown for ericp and nppatil to checkout. They will leave a passdown for staff tomorrow and/or shutdown again as needed. From ericp at snf.stanford.edu Sun Jul 11 23:54:43 2010 From: ericp at snf.stanford.edu (ericp at snf.stanford.edu) Date: Sun, 11 Jul 2010 23:54:43 -0700 Subject: Comment innotec SNF 2010-07-11 23:54:42: regened, pumping down Message-ID: Cryo was dumped. LR between cryo and chamber (chamber pumped down, cryo at atm) was 500mT/min. I recommend that the gate valve be cycled several times under vacuum before venting the chamber. (Maybe a piece of something on the seal?). From maurice at snf.stanford.edu Mon Jul 12 11:37:17 2010 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Mon, 12 Jul 2010 11:37:17 -0700 Subject: Problem innotec SNF 2010-07-11 10:14:58: can't pump down Message-ID: Eric P regened system From maurice at snf.stanford.edu Mon Jul 12 11:37:31 2010 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Mon, 12 Jul 2010 11:37:31 -0700 Subject: Comment innotec SNF 2010-07-11 10:06:38: system resetted Message-ID: Eric P regened system From maurice at snf.stanford.edu Mon Jul 12 11:38:01 2010 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Mon, 12 Jul 2010 11:38:01 -0700 Subject: Problem innotec SNF 2010-07-08 08:52:18: Pockets no being cleaned enough Message-ID: logged From maurice at snf.stanford.edu Mon Jul 12 11:38:31 2010 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Mon, 12 Jul 2010 11:38:31 -0700 Subject: Comment innotec SNF 2010-06-30 19:06:41: sample in the chamber Message-ID: removed From maurice at snf.stanford.edu Mon Jul 12 11:38:43 2010 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Mon, 12 Jul 2010 11:38:43 -0700 Subject: Comment innotec SNF 2010-07-08 10:42:40: added another 10 Au pelleta Message-ID: logged From maurice at snf.stanford.edu Mon Jul 12 11:39:00 2010 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Mon, 12 Jul 2010 11:39:00 -0700 Subject: Comment innotec SNF 2010-07-07 16:03:47: added 10 Au pellets Message-ID: logged From mzhang2 at snf.stanford.edu Mon Jul 12 13:21:26 2010 From: mzhang2 at snf.stanford.edu (mzhang2 at snf.stanford.edu) Date: Mon, 12 Jul 2010 13:21:26 -0700 Subject: Shutdown innotec SNF 2010-07-12 13:21:24: Message-ID: before I made the deposition, Si source is clogged when I rotate the crucible and I can't take it out. other source in the crucible: C3: Fe; C4: Ti; From svo at snf.stanford.edu Mon Jul 12 13:26:07 2010 From: svo at snf.stanford.edu (svo at snf.stanford.edu) Date: Mon, 12 Jul 2010 13:26:07 -0700 Subject: Comment innotec SNF 2010-07-12 13:26:07: please trim si source Message-ID: please trim si source. i had to deposit si and then vent to take out si and then pump down to proceed with other deposition! From jhaydon at snf.stanford.edu Mon Jul 12 13:40:43 2010 From: jhaydon at snf.stanford.edu (jhaydon at snf.stanford.edu) Date: Mon, 12 Jul 2010 13:40:43 -0700 Subject: Shutdown innotec SNF 2010-07-12 13:21:24: Message-ID: targets removed ok to use From jperez at snf.stanford.edu Thu Jul 15 07:16:07 2010 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Thu, 15 Jul 2010 07:16:07 -0700 Subject: Comment innotec SNF 2010-07-11 23:54:42: regened, pumping down Message-ID: Thanks for your help! From jperez at snf.stanford.edu Thu Jul 15 07:17:26 2010 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Thu, 15 Jul 2010 07:17:26 -0700 Subject: Comment innotec SNF 2010-07-08 10:16:53: New gun "flickers", go slow Message-ID: Used system and saw no flickering, power raised to 11%. From jperez at snf.stanford.edu Thu Jul 15 07:21:15 2010 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Thu, 15 Jul 2010 07:21:15 -0700 Subject: Comment innotec SNF 2010-06-20 14:40:09: clean needed -- much peeling Message-ID: Major clean was preformed on 6/22/10 From gth at snf.stanford.edu Sun Jul 18 11:39:02 2010 From: gth at snf.stanford.edu (gth at snf.stanford.edu) Date: Sun, 18 Jul 2010 11:39:02 -0700 Subject: Problem innotec SNF 2010-07-18 11:39:01: bad shutter Message-ID: When closing the shutter, one side of the shutter cap will hit the bottom metal plate. The cap is too low and tilted From gth at snf.stanford.edu Sun Jul 18 12:38:39 2010 From: gth at snf.stanford.edu (gth at snf.stanford.edu) Date: Sun, 18 Jul 2010 12:38:39 -0700 Subject: Comment innotec SNF 2010-07-18 12:38:38: shutter screwed back to position. Message-ID: From jperez at snf.stanford.edu Mon Jul 19 07:00:53 2010 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Mon, 19 Jul 2010 07:00:53 -0700 Subject: Problem innotec SNF 2010-07-18 11:39:01: bad shutter Message-ID: raised arm. From jperez at snf.stanford.edu Mon Jul 19 07:01:08 2010 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Mon, 19 Jul 2010 07:01:08 -0700 Subject: Comment innotec SNF 2010-07-18 12:38:38: shutter screwed back to position. Message-ID: Thanks From faridz at snf.stanford.edu Mon Jul 26 15:09:49 2010 From: faridz at snf.stanford.edu (faridz at snf.stanford.edu) Date: Mon, 26 Jul 2010 15:09:49 -0700 Subject: Problem innotec SNF 2010-07-26 15:09:48: chamber stuck Message-ID: I'm done with my depo, after venting the chamber for more than 6 mins, chamber failed to liftup. Notified Jeannie From emyers at snf.stanford.edu Mon Jul 26 15:22:24 2010 From: emyers at snf.stanford.edu (emyers at snf.stanford.edu) Date: Mon, 26 Jul 2010 15:22:24 -0700 Subject: Problem innotec SNF 2010-07-26 15:09:48: chamber stuck Message-ID: I was able to get the chamber lift to work. Lab member is finishing their process. From emyers at snf.stanford.edu Mon Jul 26 15:24:15 2010 From: emyers at snf.stanford.edu (emyers at snf.stanford.edu) Date: Mon, 26 Jul 2010 15:24:15 -0700 Subject: Problem innotec SNF 2010-07-26 15:24:14: Hoist Unjammed Message-ID: The hoist was jammed with the bell jar down. I was able to get it freed so the lab member could complete their process. I don't know if it will happen again. From gth at snf.stanford.edu Tue Jul 27 13:27:14 2010 From: gth at snf.stanford.edu (gth at snf.stanford.edu) Date: Tue, 27 Jul 2010 13:27:14 -0700 Subject: Problem innotec SNF 2010-07-27 13:27:10: repair Al target. Message-ID: messed up. hard to fit in the slot. From jperez at snf.stanford.edu Tue Jul 27 15:41:53 2010 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Tue, 27 Jul 2010 15:41:53 -0700 Subject: Problem innotec SNF 2010-07-27 13:27:10: repair Al target. Message-ID: OK to use. From ehe at snf.stanford.edu Wed Jul 28 16:18:09 2010 From: ehe at snf.stanford.edu (ehe at snf.stanford.edu) Date: Wed, 28 Jul 2010 16:18:09 -0700 Subject: Problem innotec SNF 2010-07-28 16:18:09: Si source missing Message-ID: SNF Si source is missing. I have my own Si source, but people who don't and were planning on using Si would probably want to know... From jperez at snf.stanford.edu Thu Jul 29 15:20:58 2010 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Thu, 29 Jul 2010 15:20:58 -0700 Subject: Problem innotec SNF 2010-07-28 16:18:09: Si source missing Message-ID: Silicon source doesn't sit well, it may get stuck when rotating. Make sure you can rotate before pumping down. If only using Si, no problem because your not rotaitng.