From tdo at snf.stanford.edu Sat Jun 5 10:30:15 2010 From: tdo at snf.stanford.edu (tdo at snf.stanford.edu) Date: Sat, 5 Jun 2010 10:30:15 -0700 Subject: Comment innotec SNF 2010-06-05 10:30:14: gold flake on o-ring Message-ID: there are a couple gold flakes smashed into the oring on the belljar (front side). pumpdown was ok though (28 mins for 5e-7) From tdo at snf.stanford.edu Sat Jun 5 10:30:47 2010 From: tdo at snf.stanford.edu (tdo at snf.stanford.edu) Date: Sat, 5 Jun 2010 10:30:47 -0700 Subject: Problem innotec SNF 2010-06-05 10:30:46: pressure spike when shutter opened Message-ID: noticed a pressure spike when the shutter was opened (>1e-6) From jperez at snf.stanford.edu Mon Jun 7 07:06:25 2010 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Mon, 7 Jun 2010 07:06:25 -0700 Subject: Shutdown innotec SNF 2010-06-07 07:06:24: Water flow off from 7 AM until 2 PM Message-ID: From jperez at snf.stanford.edu Mon Jun 7 09:59:30 2010 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Mon, 7 Jun 2010 09:59:30 -0700 Subject: Shutdown innotec SNF 2010-06-07 07:06:24: Water flow off from 7 AM until 2 PM Message-ID: Wafer flow back on. Down for regen. From jperez at snf.stanford.edu Mon Jun 7 09:59:47 2010 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Mon, 7 Jun 2010 09:59:47 -0700 Subject: Shutdown innotec SNF 2010-06-07 09:59:46: Down for regen Message-ID: From maurice at snf.stanford.edu Mon Jun 7 17:46:09 2010 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Mon, 7 Jun 2010 17:46:09 -0700 Subject: Shutdown innotec SNF 2010-06-07 09:59:46: Down for regen Message-ID: Cooling after regen System can be used once temp is below 17k From maurice at snf.stanford.edu Mon Jun 7 17:46:48 2010 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Mon, 7 Jun 2010 17:46:48 -0700 Subject: Problem innotec SNF 2010-06-07 17:46:47: Innotec can be used once temp is below 17k Message-ID: Cooling after regen System can be used once temp is below 17k From jperez at snf.stanford.edu Tue Jun 8 07:29:03 2010 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Tue, 8 Jun 2010 07:29:03 -0700 Subject: Problem innotec SNF 2010-06-07 17:46:47: Innotec can be used once temp is below 17k Message-ID: Regen complete. From jonesra at snf.stanford.edu Wed Jun 9 17:16:00 2010 From: jonesra at snf.stanford.edu (jonesra at snf.stanford.edu) Date: Wed, 9 Jun 2010 17:16:00 -0700 Subject: Comment innotec SNF 2010-06-09 17:16:00: gold looked odd Message-ID: May be contaminated? inspect before using From slcheng at snf.stanford.edu Thu Jun 10 23:39:16 2010 From: slcheng at snf.stanford.edu (slcheng at snf.stanford.edu) Date: Thu, 10 Jun 2010 23:39:16 -0700 Subject: Problem innotec SNF 2010-06-10 23:39:14: C2 position + Al target does not look good. Message-ID: From jperez at snf.stanford.edu Fri Jun 11 07:06:05 2010 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Fri, 11 Jun 2010 07:06:05 -0700 Subject: Comment innotec SNF 2010-06-09 17:16:00: gold looked odd Message-ID: I spoke with the prevous users and decided OK to use. From jperez at snf.stanford.edu Fri Jun 11 07:06:51 2010 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Fri, 11 Jun 2010 07:06:51 -0700 Subject: Comment innotec SNF 2010-06-05 10:30:14: gold flake on o-ring Message-ID: Removed flakes. From jperez at snf.stanford.edu Fri Jun 11 13:12:33 2010 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Fri, 11 Jun 2010 13:12:33 -0700 Subject: Problem innotec SNF 2010-06-05 10:30:46: pressure spike when shutter opened Message-ID: Since it hasn't happen again (or at least reported) it most likely was a seal burp. From jperez at snf.stanford.edu Fri Jun 11 13:13:57 2010 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Fri, 11 Jun 2010 13:13:57 -0700 Subject: Problem innotec SNF 2010-06-10 23:39:14: C2 position + Al target does not look good. Message-ID: I took a look at the Aluminum starter source and doesn't look different (edges oxidized). OK to use. From dkozak at snf.stanford.edu Sun Jun 20 14:40:10 2010 From: dkozak at snf.stanford.edu (dkozak at snf.stanford.edu) Date: Sun, 20 Jun 2010 14:40:10 -0700 Subject: Comment innotec SNF 2010-06-20 14:40:09: clean needed -- much peeling Message-ID: Hello, planetary and side shield are peeling large films of metals. From narii at snf.stanford.edu Mon Jun 21 00:50:17 2010 From: narii at snf.stanford.edu (narii at snf.stanford.edu) Date: Mon, 21 Jun 2010 00:50:17 -0700 Subject: Problem innotec SNF 2010-06-21 00:50:17: Ti source fell into the hole Message-ID: While loading Ti source, it fell into the hole in front of the crucible. Sorry for the trouble. From dkozak at snf.stanford.edu Mon Jun 21 02:52:58 2010 From: dkozak at snf.stanford.edu (dkozak at snf.stanford.edu) Date: Mon, 21 Jun 2010 02:52:58 -0700 Subject: Comment innotec SNF 2010-06-21 02:52:57: interlock and jumpy dep rate Message-ID: Message on screen: "Interlock WFS2" flashes sometimes, does not prevent operation Dep. rate was somewhat jumpy (0.5 A/s differfences in 10 s, up and down). Check crystal From jhaydon at snf.stanford.edu Mon Jun 21 09:08:05 2010 From: jhaydon at snf.stanford.edu (jhaydon at snf.stanford.edu) Date: Mon, 21 Jun 2010 09:08:05 -0700 Subject: Comment innotec SNF 2010-06-21 02:52:57: interlock and jumpy dep rate Message-ID: wfs2 cable was disconnected reconnected cable From jhaydon at snf.stanford.edu Mon Jun 21 09:21:54 2010 From: jhaydon at snf.stanford.edu (jhaydon at snf.stanford.edu) Date: Mon, 21 Jun 2010 09:21:54 -0700 Subject: Problem innotec SNF 2010-06-21 00:50:17: Ti source fell into the hole Message-ID: Ti source recovered From jimkruger at snf.stanford.edu Mon Jun 21 11:33:59 2010 From: jimkruger at snf.stanford.edu (jimkruger at snf.stanford.edu) Date: Mon, 21 Jun 2010 11:33:59 -0700 Subject: Problem innotec SNF 2010-06-21 11:33:58: only 3 Au pellets left Message-ID: From maurice at snf.stanford.edu Mon Jun 21 11:38:45 2010 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Mon, 21 Jun 2010 11:38:45 -0700 Subject: Problem innotec SNF 2010-06-21 11:33:58: only 3 Au pellets left Message-ID: added 20 pellets ( new larger size pellets) From jimkruger at snf.stanford.edu Mon Jun 21 14:17:50 2010 From: jimkruger at snf.stanford.edu (jimkruger at snf.stanford.edu) Date: Mon, 21 Jun 2010 14:17:50 -0700 Subject: Problem innotec SNF 2010-06-21 14:17:50: No Ni pellets Message-ID: But the Ni starter is nearly new so OK for now. From maurice at snf.stanford.edu Mon Jun 21 15:04:34 2010 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Mon, 21 Jun 2010 15:04:34 -0700 Subject: Problem innotec SNF 2010-06-21 14:17:50: No Ni pellets Message-ID: added 13 Ni pellets From jperez at snf.stanford.edu Tue Jun 22 08:25:26 2010 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Tue, 22 Jun 2010 08:25:26 -0700 Subject: Shutdown innotec SNF 2010-06-22 08:25:26: Shield change Message-ID: From jperez at snf.stanford.edu Tue Jun 22 15:27:04 2010 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Tue, 22 Jun 2010 15:27:04 -0700 Subject: Shutdown innotec SNF 2010-06-22 08:25:26: Shield change Message-ID: Shield change, coating Chamber have been completed. OK to use. From fanpy at snf.stanford.edu Wed Jun 30 19:06:42 2010 From: fanpy at snf.stanford.edu (fanpy at snf.stanford.edu) Date: Wed, 30 Jun 2010 19:06:42 -0700 Subject: Comment innotec SNF 2010-06-30 19:06:41: sample in the chamber Message-ID: When the fire alarm came up, I finished my deposition and turned off the main power but did not get to start venting. Could the next user please help me unload my samples (they are THREE dummy wafers with kapton taped chip on them) and leave them on the table? Thank you so much for your help!