From jperez at snf.stanford.edu Thu Jun 2 10:21:41 2011 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Thu, 2 Jun 2011 10:21:41 -0700 Subject: Comment innotec SNF 2011-05-31 19:37:59: no pt pellets Message-ID: added pellets From jperez at snf.stanford.edu Thu Jun 2 10:22:59 2011 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Thu, 2 Jun 2011 10:22:59 -0700 Subject: Comment innotec SNF 2011-05-29 23:33:13: Al target became hot Message-ID: Set sitting in crucible correctly From jperez at snf.stanford.edu Thu Jun 2 10:26:01 2011 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Thu, 2 Jun 2011 10:26:01 -0700 Subject: Comment innotec SNF 2011-05-29 18:39:27: Cryo pump is turned off. Message-ID: notified previous User. From jperez at snf.stanford.edu Thu Jun 2 10:27:37 2011 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Thu, 2 Jun 2011 10:27:37 -0700 Subject: Comment innotec SNF 2011-05-26 23:11:53: Beam is wide indeed Message-ID: Jim adjusted magnets. Run three metals, beam checked out OK. From jperez at snf.stanford.edu Thu Jun 2 10:28:08 2011 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Thu, 2 Jun 2011 10:28:08 -0700 Subject: Problem innotec SNF 2011-05-26 17:09:42: Beam is Wide Message-ID: Jim H adjust magnets. From jperez at snf.stanford.edu Thu Jun 2 10:28:55 2011 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Thu, 2 Jun 2011 10:28:55 -0700 Subject: Problem innotec SNF 2011-05-26 15:13:34: Tests will be read in the morning 2/27/11 Message-ID: Test read next morning and were normal as my other tests. From jperez at snf.stanford.edu Thu Jun 2 10:30:00 2011 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Thu, 2 Jun 2011 10:30:00 -0700 Subject: Comment innotec SNF 2011-05-31 23:26:43: Au dep rate too low? Message-ID: You have to make sure the pocket is clean and starter source is sitting flat on the bottom. From jperez at snf.stanford.edu Fri Jun 3 07:22:36 2011 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Fri, 3 Jun 2011 07:22:36 -0700 Subject: Shutdown innotec SNF 2011-06-03 07:22:36: Starting Regen Message-ID: From jperez at snf.stanford.edu Fri Jun 3 11:21:22 2011 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Fri, 3 Jun 2011 11:21:22 -0700 Subject: Shutdown innotec SNF 2011-06-03 07:22:36: Starting Regen Message-ID: REGEN COMPLETE. From ajamo at snf.stanford.edu Wed Jun 8 11:33:18 2011 From: ajamo at snf.stanford.edu (ajamo at snf.stanford.edu) Date: Wed, 8 Jun 2011 11:33:18 -0700 Subject: Comment innotec SNF 2011-06-08 11:33:18: Chamber got stuck, would not go down Message-ID: Chamber got stuck in the up position, it would not move when pushing down toggles. Jim fixed it, but be aware. From jimkruger at snf.stanford.edu Thu Jun 9 11:45:18 2011 From: jimkruger at snf.stanford.edu (jimkruger at snf.stanford.edu) Date: Thu, 9 Jun 2011 11:45:18 -0700 Subject: Comment innotec SNF 2011-06-09 11:45:17: only 3 Ti pellets left Message-ID: From jperez at snf.stanford.edu Thu Jun 9 16:09:00 2011 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Thu, 9 Jun 2011 16:09:00 -0700 Subject: Comment innotec SNF 2011-06-09 11:45:17: only 3 Ti pellets left Message-ID: Added Ti pellets From jperez at snf.stanford.edu Thu Jun 9 16:09:55 2011 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Thu, 9 Jun 2011 16:09:55 -0700 Subject: Comment innotec SNF 2011-06-08 11:33:18: Chamber got stuck, would not go down Message-ID: May happen again. Sometimes the hoist thinks its down already. From jperez at snf.stanford.edu Thu Jun 9 16:10:21 2011 From: jperez at snf.stanford.edu (jperez at snf.stanford.edu) Date: Thu, 9 Jun 2011 16:10:21 -0700 Subject: Comment innotec SNF 2011-05-26 19:00:04: Both beam size and power ok Message-ID: Magnets adjusted, OK now. From maurice at snf.stanford.edu Fri Jun 10 14:23:12 2011 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Fri, 10 Jun 2011 14:23:12 -0700 Subject: Problem innotec SNF 2011-06-10 14:23:12: no planitary rotation Message-ID: Jim H is coming to investigate From jhaydon at snf.stanford.edu Fri Jun 10 16:13:03 2011 From: jhaydon at snf.stanford.edu (jhaydon at snf.stanford.edu) Date: Fri, 10 Jun 2011 16:13:03 -0700 Subject: Problem innotec SNF 2011-06-10 14:23:12: no planitary rotation Message-ID: replaced damaged bearings in planetary gear From zpatel at snf.stanford.edu Mon Jun 13 19:28:24 2011 From: zpatel at snf.stanford.edu (zpatel at snf.stanford.edu) Date: Mon, 13 Jun 2011 19:28:24 -0700 Subject: Comment innotec SNF 2011-06-13 19:28:23: Au very low Message-ID: From maurice at snf.stanford.edu Tue Jun 14 09:14:50 2011 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Tue, 14 Jun 2011 09:14:50 -0700 Subject: Comment innotec SNF 2011-06-13 19:28:23: Au very low Message-ID: added 37 pellets to source (melted in) From zpatel at snf.stanford.edu Tue Jun 14 17:57:39 2011 From: zpatel at snf.stanford.edu (zpatel at snf.stanford.edu) Date: Tue, 14 Jun 2011 17:57:39 -0700 Subject: Comment innotec SNF 2011-06-14 17:57:38: Big dent in Au pellet Message-ID: Particles on the chamber floor. Previous user did not do proper inspection/cleaning Au pellet has a big dent From fanpy at snf.stanford.edu Fri Jun 17 22:45:53 2011 From: fanpy at snf.stanford.edu (fanpy at snf.stanford.edu) Date: Fri, 17 Jun 2011 22:45:53 -0700 Subject: Comment innotec SNF 2011-06-17 22:45:52: Au target low Message-ID: and no pellets From altamash at snf.stanford.edu Sat Jun 18 14:25:42 2011 From: altamash at snf.stanford.edu (altamash at snf.stanford.edu) Date: Sat, 18 Jun 2011 14:25:42 -0700 Subject: Problem innotec SNF 2011-06-18 14:25:42: Cryopump at 18K Message-ID: I started venting the chamber when I came in and the cryopump temperature was at 18-19k. From altamash at snf.stanford.edu Sat Jun 18 15:30:41 2011 From: altamash at snf.stanford.edu (altamash at snf.stanford.edu) Date: Sat, 18 Jun 2011 15:30:41 -0700 Subject: Comment innotec SNF 2011-06-18 15:30:40: cryopump back at 14k Message-ID: vented the system for 30mins to cool down the cryo. From altamash at snf.stanford.edu Sat Jun 18 16:04:13 2011 From: altamash at snf.stanford.edu (altamash at snf.stanford.edu) Date: Sat, 18 Jun 2011 16:04:13 -0700 Subject: Problem innotec SNF 2011-06-18 16:04:13: Cryopump back to 19K during deposition Message-ID: Please use with caution. I am not sure if the machine needs to be shutdown! From altamash at snf.stanford.edu Sat Jun 18 16:04:42 2011 From: altamash at snf.stanford.edu (altamash at snf.stanford.edu) Date: Sat, 18 Jun 2011 16:04:42 -0700 Subject: Comment innotec SNF 2011-06-18 16:04:41: Gold source below 50g Message-ID: Looks very thin From hrleebh at snf.stanford.edu Sun Jun 19 16:22:04 2011 From: hrleebh at snf.stanford.edu (hrleebh at snf.stanford.edu) Date: Sun, 19 Jun 2011 16:22:04 -0700 Subject: Comment innotec SNF 2011-06-19 16:22:04: Au source: 36g now Message-ID: need more pellets From maurice at snf.stanford.edu Mon Jun 20 10:00:38 2011 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Mon, 20 Jun 2011 10:00:38 -0700 Subject: Comment innotec SNF 2011-06-19 16:22:04: Au source: 36g now Message-ID: Gold added now 77.6 gram From maurice at snf.stanford.edu Mon Jun 20 10:00:46 2011 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Mon, 20 Jun 2011 10:00:46 -0700 Subject: Comment innotec SNF 2011-06-18 16:04:41: Gold source below 50g Message-ID: Gold added now 77.6 gram From maurice at snf.stanford.edu Mon Jun 20 10:00:58 2011 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Mon, 20 Jun 2011 10:00:58 -0700 Subject: Comment innotec SNF 2011-06-17 22:45:52: Au target low Message-ID: Gold added now 77.6 gram From maurice at snf.stanford.edu Mon Jun 20 10:01:10 2011 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Mon, 20 Jun 2011 10:01:10 -0700 Subject: Comment innotec SNF 2011-06-14 17:57:38: Big dent in Au pellet Message-ID: Gold added now 77.6 gram From jimkruger at snf.stanford.edu Mon Jun 20 13:02:28 2011 From: jimkruger at snf.stanford.edu (jimkruger at snf.stanford.edu) Date: Mon, 20 Jun 2011 13:02:28 -0700 Subject: Problem innotec SNF 2011-06-20 13:02:27: Ni pellets all gone Message-ID: The plastic bag had been melted by the last user. WAIT LONGER BEFORE VENTING! From yuxinz at snf.stanford.edu Tue Jun 21 19:37:28 2011 From: yuxinz at snf.stanford.edu (yuxinz at snf.stanford.edu) Date: Tue, 21 Jun 2011 19:37:28 -0700 Subject: Problem innotec SNF 2011-06-21 19:37:28: Cryopump temp at 16K Message-ID: From maurice at snf.stanford.edu Wed Jun 22 15:06:48 2011 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Wed, 22 Jun 2011 15:06:48 -0700 Subject: Comment innotec SNF 2011-06-22 15:06:47: Ni pellets added to box Message-ID: 16 big Ni pellets added to box From jimkruger at snf.stanford.edu Fri Jun 24 12:14:13 2011 From: jimkruger at snf.stanford.edu (jimkruger at snf.stanford.edu) Date: Fri, 24 Jun 2011 12:14:13 -0700 Subject: Comment innotec SNF 2011-06-24 12:14:13: High cryo T instructions Message-ID: The Cryo Temp has been reading a little hifg on the screen. Ceck the temp on the "On-Board" pannel in back to see that it is in spec (<16 k), then proceed as usual. If the front screen "pump temp" reaches 25C, like on a long hot dep, e.g Tungsten, the system will however abort even though the "back" T is OK. From kcbalram at snf.stanford.edu Sat Jun 25 14:39:24 2011 From: kcbalram at snf.stanford.edu (kcbalram at snf.stanford.edu) Date: Sat, 25 Jun 2011 14:39:24 -0700 Subject: Problem innotec SNF 2011-06-25 14:39:23: Cr target has been punched through Message-ID: The Cr target has a hole all all the way through..... From zpatel at snf.stanford.edu Tue Jun 28 18:33:52 2011 From: zpatel at snf.stanford.edu (zpatel at snf.stanford.edu) Date: Tue, 28 Jun 2011 18:33:52 -0700 Subject: Comment innotec SNF 2011-06-28 18:33:52: Source material low in depth Message-ID: Several source material are very low in thickness (depth) Added several pellet to Al, Ni and Ti From ajamo at snf.stanford.edu Thu Jun 30 11:54:09 2011 From: ajamo at snf.stanford.edu (ajamo at snf.stanford.edu) Date: Thu, 30 Jun 2011 11:54:09 -0700 Subject: Shutdown innotec SNF 2011-06-30 11:54:09: Cryo temp @ 16K to 19K Message-ID: Cryo temp started at 14 K but went up to 19K during dep. It recovered back to 15K when I unloaded, but next dep it went back up to 17 - 18K. Jim is going to do a regen From jhaydon at snf.stanford.edu Thu Jun 30 15:35:55 2011 From: jhaydon at snf.stanford.edu (jhaydon at snf.stanford.edu) Date: Thu, 30 Jun 2011 15:35:55 -0700 Subject: Shutdown innotec SNF 2011-06-30 11:54:09: Cryo temp @ 16K to 19K Message-ID: ok to use when cryo is below 17K