From kimsangb at snf.stanford.edu Sun May 3 03:03:21 2009 From: kimsangb at snf.stanford.edu (kimsangb at snf.stanford.edu) Date: Sun, 3 May 2009 03:03:21 -0700 Subject: Problem karlsuss SNF 2009-05-03 03:03:20: Red led blinking for failure:lamp life/power Message-ID: From kimsangb at snf.stanford.edu Sun May 3 03:05:13 2009 From: kimsangb at snf.stanford.edu (kimsangb at snf.stanford.edu) Date: Sun, 3 May 2009 03:05:13 -0700 Subject: Problem karlsuss SNF 2009-05-03 03:05:12: Red LED blinking for failure:lamp life/power Message-ID: Is it time for lamp change? From gsosa at snf.stanford.edu Mon May 4 13:25:16 2009 From: gsosa at snf.stanford.edu (gsosa at snf.stanford.edu) Date: Mon, 4 May 2009 13:25:16 -0700 Subject: Problem karlsuss SNF 2009-05-03 03:03:20: Red led blinking for failure:lamp life/power Message-ID: Replaced UV lamp. Adjusted lamp position and calibrated exposure. Intensity set to 15.0 Mw/cm2, Uniformity: 2.3% From gsosa at snf.stanford.edu Mon May 4 13:25:40 2009 From: gsosa at snf.stanford.edu (gsosa at snf.stanford.edu) Date: Mon, 4 May 2009 13:25:40 -0700 Subject: Problem karlsuss SNF 2009-05-03 03:05:12: Red LED blinking for failure:lamp life/power Message-ID: Replaced UV lamp. Adjusted lamp position and calibrated exposure. Intensity set to 15.0 Mw/cm2, Uniformity: 2.3% From gsosa at snf.stanford.edu Wed May 13 13:25:27 2009 From: gsosa at snf.stanford.edu (gsosa at snf.stanford.edu) Date: Wed, 13 May 2009 13:25:27 -0700 Subject: Problem karlsuss SNF 2009-04-28 21:07:45: Backside alignment problems Message-ID: Verified X travel limits of BSA microscopes against system specification. Both left and right microscopes meet the specification of 16 to 43.5mm of travel before hitting the software limits. When both microscopes are at their widest position, the distance between the objectives is 87mm as per specification. If in the fast mode, the microscope can travel slightly past the software limits at which point you will get a limit error displayed and an audible beep. To recover, the microscope must be moved in the opposite direction using the arrow button. The error will continue to be displayed and audible beep until the microscope travels back within the software boundary. Also, each press of the arrow button will only move the microscope 0.01mm increments in either fast or slow mode until it is within the software boundary. At this time the microscope operation returns to normal. BSA microscope operation OK From gsosa at snf.stanford.edu Fri May 29 08:53:58 2009 From: gsosa at snf.stanford.edu (gsosa at snf.stanford.edu) Date: Fri, 29 May 2009 08:53:58 -0700 Subject: Comment karlsuss SNF 2009-05-29 08:53:57: Scheduled lamp change Message-ID: Replaced UV lamp. Set up UV lamp and calibrated power supply. Intensity set to: 15 mw/cm2 , Uniformity: .9 % From panjun at snf.stanford.edu Sun May 31 21:47:25 2009 From: panjun at snf.stanford.edu (panjun at snf.stanford.edu) Date: Sun, 31 May 2009 21:47:25 -0700 Subject: Problem karlsuss SNF 2009-05-31 21:47:25: load button is flashing Message-ID: load button is flashing when i came to tool. none of the buttons work, can't change mask.