From lindaw at snf.stanford.edu Tue Oct 2 11:20:45 2007 From: lindaw at snf.stanford.edu (lindaw at snf.stanford.edu) Date: Tue, 2 Oct 2007 11:20:45 -0700 Subject: Comment karlsuss2 SNF 2007-10-02 11:20:45: lamp power supply beeping during exposure Message-ID: From gsosa at snf.stanford.edu Wed Oct 3 08:10:04 2007 From: gsosa at snf.stanford.edu (gsosa at snf.stanford.edu) Date: Wed, 3 Oct 2007 08:10:04 -0700 Subject: Comment karlsuss2 SNF 2007-10-02 11:20:45: lamp power supply beeping during exposure Message-ID: Checked and recalibrated lamp power supply. Intensity is at 15 Mw/cm2 and uniformity is 1.6 %. GS From lindaw at snf.stanford.edu Tue Oct 9 15:35:54 2007 From: lindaw at snf.stanford.edu (lindaw at snf.stanford.edu) Date: Tue, 9 Oct 2007 15:35:54 -0700 Subject: Comment karlsuss2 SNF 2007-10-09 15:35:53: x micrometer is sticking a little bit Message-ID: and squeaking sometimes when turning when the chuck is fairly centered. From vilanova at snf.stanford.edu Wed Oct 10 09:15:45 2007 From: vilanova at snf.stanford.edu (vilanova at snf.stanford.edu) Date: Wed, 10 Oct 2007 09:15:45 -0700 Subject: Comment karlsuss2 SNF 2007-10-09 15:35:53: x micrometer is sticking a little bit Message-ID: Lubricated micrometer. From lindaw at snf.stanford.edu Fri Oct 12 10:43:07 2007 From: lindaw at snf.stanford.edu (lindaw at snf.stanford.edu) Date: Fri, 12 Oct 2007 10:43:07 -0700 Subject: Comment karlsuss2 SNF 2007-10-12 10:43:07: enter key is peeling Message-ID: From nborghi at snf.stanford.edu Sat Oct 13 10:58:43 2007 From: nborghi at snf.stanford.edu (nborghi at snf.stanford.edu) Date: Sat, 13 Oct 2007 10:58:43 -0700 Subject: Comment karlsuss2 SNF 2007-10-13 10:58:42: vacuum seal not in marked area (>0.4) Message-ID: From vilanova at snf.stanford.edu Mon Oct 15 07:23:28 2007 From: vilanova at snf.stanford.edu (vilanova at snf.stanford.edu) Date: Mon, 15 Oct 2007 07:23:28 -0700 Subject: Comment karlsuss2 SNF 2007-10-12 10:43:07: enter key is peeling Message-ID: tape it down. From vilanova at snf.stanford.edu Mon Oct 15 07:23:57 2007 From: vilanova at snf.stanford.edu (vilanova at snf.stanford.edu) Date: Mon, 15 Oct 2007 07:23:57 -0700 Subject: Comment karlsuss2 SNF 2007-10-13 10:58:42: vacuum seal not in marked area (>0.4) Message-ID: vacuum seems to be normal, checked and tested, ready to use. From alexalex at snf.stanford.edu Thu Oct 25 04:41:19 2007 From: alexalex at snf.stanford.edu (alexalex at snf.stanford.edu) Date: Thu, 25 Oct 2007 04:41:19 -0700 Subject: Comment karlsuss2 SNF 2007-10-25 04:41:17: Machine rebooted Message-ID: screen said that the machine was "overcurrent" and is restarting. From alexalex at snf.stanford.edu Thu Oct 25 05:33:46 2007 From: alexalex at snf.stanford.edu (alexalex at snf.stanford.edu) Date: Thu, 25 Oct 2007 05:33:46 -0700 Subject: Comment karlsuss2 SNF 2007-10-25 05:33:45: machine rebooted Message-ID: screen said that machine went overcurrent then restarted. From gsosa at snf.stanford.edu Fri Oct 26 07:26:16 2007 From: gsosa at snf.stanford.edu (gsosa at snf.stanford.edu) Date: Fri, 26 Oct 2007 07:26:16 -0700 Subject: Shutdown karlsuss2 SNF 2007-10-26 07:26:15: Scheduled lamp change Message-ID: Replacing the UV lamp. GS From gsosa at snf.stanford.edu Fri Oct 26 08:28:11 2007 From: gsosa at snf.stanford.edu (gsosa at snf.stanford.edu) Date: Fri, 26 Oct 2007 08:28:11 -0700 Subject: Shutdown karlsuss2 SNF 2007-10-26 07:26:15: Scheduled lamp change Message-ID: Replaced and setup new UV lamp. Calibrated exposure. CH #1 15Mw CH#2 30Mw