From yiyang at snf.stanford.edu Mon Mar 2 23:46:20 2009 From: yiyang at snf.stanford.edu (yiyang at snf.stanford.edu) Date: Mon, 2 Mar 2009 23:46:20 -0800 Subject: Problem raith SNF 2009-03-02 23:46:19: water flow down Message-ID: water flow failure error was reported. I unloaded the previous user's chip, but will not start my session From ahazeghi at snf.stanford.edu Tue Mar 3 01:14:17 2009 From: ahazeghi at snf.stanford.edu (ahazeghi at snf.stanford.edu) Date: Tue, 3 Mar 2009 01:14:17 -0800 Subject: Problem raith SNF 2009-03-03 01:14:16: water flow Message-ID: LEO SERV status indicates water flow has been resumed, turbo in stanfby mode however it is not possible to pump the load lock From xutian at snf.stanford.edu Tue Mar 3 12:04:55 2009 From: xutian at snf.stanford.edu (xutian at snf.stanford.edu) Date: Tue, 3 Mar 2009 12:04:55 -0800 Subject: Problem raith SNF 2009-03-03 12:04:55: Vacuum in stage chamber not ready Message-ID: The pop up error message is "Please start pumping, when ready press OK", can not begin loading. From jwc at snf.stanford.edu Tue Mar 3 12:31:00 2009 From: jwc at snf.stanford.edu (jwc at snf.stanford.edu) Date: Tue, 3 Mar 2009 12:31:00 -0800 Subject: Problem raith SNF 2009-03-02 23:46:19: water flow down Message-ID: added 1 liter of pure water to cooling loop. Not sure where it leaked out of or evaporated. unusual raith has been called and requested to flush out all the cooling loop BEFORE replacing to our chiller. Currently on a loaner chiller with no check valve to prevent reverse flow. From jwc at snf.stanford.edu Tue Mar 3 12:31:06 2009 From: jwc at snf.stanford.edu (jwc at snf.stanford.edu) Date: Tue, 3 Mar 2009 12:31:06 -0800 Subject: Problem raith SNF 2009-03-03 01:14:16: water flow Message-ID: From jwc at snf.stanford.edu Tue Mar 3 12:32:20 2009 From: jwc at snf.stanford.edu (jwc at snf.stanford.edu) Date: Tue, 3 Mar 2009 12:32:20 -0800 Subject: Problem raith SNF 2009-03-03 12:04:55: Vacuum in stage chamber not ready Message-ID: vacuum set point for system chanber did not make as it was over the compliance setting. Reset all hardware interfaces and now readings are normal. It will take all day to reqach system chamber base pressure but assisted current user with Loading his sample and he should be fine by exposure end time. JWC From jesselu at snf.stanford.edu Tue Mar 17 09:11:52 2009 From: jesselu at snf.stanford.edu (jesselu at snf.stanford.edu) Date: Tue, 17 Mar 2009 09:11:52 -0700 Subject: Shutdown raith SNF 2009-03-17 09:11:52: water pump problems Message-ID: came in this morning, water flow too low to operate machine. James asked to put the raith in red-light mode. From jwc at snf.stanford.edu Tue Mar 17 15:46:01 2009 From: jwc at snf.stanford.edu (jwc at snf.stanford.edu) Date: Tue, 17 Mar 2009 15:46:01 -0700 Subject: Shutdown raith SNF 2009-03-17 09:11:52: water pump problems Message-ID: flushed cooli8ng loop after disinfecting with chlorox bleach and water