From king at snf.stanford.edu Sat Jan 12 01:25:49 2008 From: king at snf.stanford.edu (king at snf.stanford.edu) Date: Sat, 12 Jan 2008 01:25:49 -0800 Subject: Problem thermcopoly1 SNF 2008-01-12 01:25:49: Boat motor stays on Message-ID: It's fighting the vacuum trying to pull the boat out. From king at snf.stanford.edu Sat Jan 12 01:28:29 2008 From: king at snf.stanford.edu (king at snf.stanford.edu) Date: Sat, 12 Jan 2008 01:28:29 -0800 Subject: Problem thermcopoly1 SNF 2008-01-12 01:28:29: Rail drags a little on the tube Message-ID: The rail scrapes on the tube for a short time when it's about half way in. Does it while going both in and out, with wafers loaded or not. From tberg at snf.stanford.edu Mon Jan 14 10:56:26 2008 From: tberg at snf.stanford.edu (tberg at snf.stanford.edu) Date: Mon, 14 Jan 2008 10:56:26 -0800 Subject: Problem thermcopoly1 SNF 2008-01-12 01:28:29: Rail drags a little on the tube Message-ID: Adjusted cantilever no drag From tberg at snf.stanford.edu Mon Jan 14 10:56:52 2008 From: tberg at snf.stanford.edu (tberg at snf.stanford.edu) Date: Mon, 14 Jan 2008 10:56:52 -0800 Subject: Problem thermcopoly1 SNF 2008-01-12 01:25:49: Boat motor stays on Message-ID: Adjusted cantilever no drag no problem on standby From mdickey at snf.stanford.edu Wed Jan 16 07:38:28 2008 From: mdickey at snf.stanford.edu (mdickey at snf.stanford.edu) Date: Wed, 16 Jan 2008 07:38:28 -0800 Subject: Comment thermcopoly1 SNF 2008-01-16 07:38:28: Filters Message-ID: Replaced exhaust filters for the pump From tberg at snf.stanford.edu Wed Jan 23 14:02:24 2008 From: tberg at snf.stanford.edu (tberg at snf.stanford.edu) Date: Wed, 23 Jan 2008 14:02:24 -0800 Subject: Problem thermcopoly1 SNF 2008-01-23 14:02:24: No PH3 Message-ID: Cylinder is still off From king at snf.stanford.edu Wed Jan 23 15:24:19 2008 From: king at snf.stanford.edu (king at snf.stanford.edu) Date: Wed, 23 Jan 2008 15:24:19 -0800 Subject: Problem thermcopoly1 SNF 2008-01-23 15:24:19: Boat motor is on during standby Message-ID: It's fighting against the vacuum again and sounds terrible. I'm not using it,, just hearing a problem. If this isn't a problem just let us know why and we'll stop writing it up. But it sounds as though it's going to burn out and that will probably mean a delay while parts are ordered. From mdickey at snf.stanford.edu Thu Jan 24 06:23:17 2008 From: mdickey at snf.stanford.edu (mdickey at snf.stanford.edu) Date: Thu, 24 Jan 2008 06:23:17 -0800 Subject: Problem thermcopoly1 SNF 2008-01-23 15:24:19: Boat motor is on during standby Message-ID: It appears fine with no sounds at this time From tberg at snf.stanford.edu Fri Jan 25 09:29:21 2008 From: tberg at snf.stanford.edu (tberg at snf.stanford.edu) Date: Fri, 25 Jan 2008 09:29:21 -0800 Subject: Problem thermcopoly1 SNF 2008-01-23 14:02:24: No PH3 Message-ID: PH3 back in service From masaharu at snf.stanford.edu Mon Jan 28 05:34:09 2008 From: masaharu at snf.stanford.edu (masaharu at snf.stanford.edu) Date: Mon, 28 Jan 2008 05:34:09 -0800 Subject: Problem thermcopoly1 SNF 2008-01-28 05:34:08: Boat motor problem Message-ID: (1)I saw the same problem as robin's. I heard fighting sounds during the first pumping. The recipe couldn't proceed further, so I aborted it and run POLYOUT and STBYPOLY. (2)When I pull the out, I found that the boat position is quite off from the nominal "boat out"-labeled position. As a result, boat couldn't be completely close. Now, tube is in atmosphere. (3)Since pumping was failed leaving the tube open, I guess pump was down, to my knowledge. From masaharu at snf.stanford.edu Mon Jan 28 05:51:28 2008 From: masaharu at snf.stanford.edu (masaharu at snf.stanford.edu) Date: Mon, 28 Jan 2008 05:51:28 -0800 Subject: Shutdown thermcopoly1 SNF 2008-01-28 05:51:27: the reason above Message-ID: From tberg at snf.stanford.edu Mon Jan 28 07:03:37 2008 From: tberg at snf.stanford.edu (tberg at snf.stanford.edu) Date: Mon, 28 Jan 2008 07:03:37 -0800 Subject: Comment thermcopoly1 SNF 2008-01-16 07:38:28: Filters Message-ID: exhaust filters on pump changed From tberg at snf.stanford.edu Mon Jan 28 07:04:03 2008 From: tberg at snf.stanford.edu (tberg at snf.stanford.edu) Date: Mon, 28 Jan 2008 07:04:03 -0800 Subject: Comment thermcopoly1 SNF 2008-01-28 07:04:01: TC sheath is broken Message-ID: From tberg at snf.stanford.edu Mon Jan 28 07:04:53 2008 From: tberg at snf.stanford.edu (tberg at snf.stanford.edu) Date: Mon, 28 Jan 2008 07:04:53 -0800 Subject: Problem thermcopoly1 SNF 2008-01-28 05:34:08: Boat motor problem Message-ID: Did boat cal and update loader is fine From tberg at snf.stanford.edu Mon Jan 28 10:04:42 2008 From: tberg at snf.stanford.edu (tberg at snf.stanford.edu) Date: Mon, 28 Jan 2008 10:04:42 -0800 Subject: Shutdown thermcopoly1 SNF 2008-01-28 05:51:27: the reason above Message-ID: Boat caled and updated TC sheath replaced From tberg at snf.stanford.edu Mon Jan 28 10:05:00 2008 From: tberg at snf.stanford.edu (tberg at snf.stanford.edu) Date: Mon, 28 Jan 2008 10:05:00 -0800 Subject: Comment thermcopoly1 SNF 2008-01-28 07:04:01: TC sheath is broken Message-ID: Boat caled and updated TC sheath replaced