From tberg at snf.stanford.edu Tue Jan 5 08:57:00 2010 From: tberg at snf.stanford.edu (tberg at snf.stanford.edu) Date: Tue, 5 Jan 2010 08:57:00 -0800 Subject: Shutdown thermcopoly1 SNF 2009-12-22 08:15:14: pump out for rebuild Message-ID: Pump is back and pumping. Needs test From tberg at snf.stanford.edu Tue Jan 5 08:57:09 2010 From: tberg at snf.stanford.edu (tberg at snf.stanford.edu) Date: Tue, 5 Jan 2010 08:57:09 -0800 Subject: Problem thermcopoly1 SNF 2010-01-05 08:57:09: Needs test Message-ID: From ludwig at snf.stanford.edu Tue Jan 5 12:39:06 2010 From: ludwig at snf.stanford.edu (ludwig at snf.stanford.edu) Date: Tue, 5 Jan 2010 12:39:06 -0800 Subject: Problem thermcopoly1 SNF 2010-01-05 12:39:06: run fail, door did close Message-ID: the cantilever did not close the door, failed the leak test, aborted the run: reload the program, the cantilever did not start only on manual mode. When reached the end, it stopped again. I had to push it in order to close but it failed the leak test again. one more: the loading motor is still on From tberg at snf.stanford.edu Tue Jan 5 14:05:37 2010 From: tberg at snf.stanford.edu (tberg at snf.stanford.edu) Date: Tue, 5 Jan 2010 14:05:37 -0800 Subject: Comment thermcopoly1 SNF 2009-11-03 07:05:05: Oil Message-ID: noted From tberg at snf.stanford.edu Tue Jan 5 14:05:48 2010 From: tberg at snf.stanford.edu (tberg at snf.stanford.edu) Date: Tue, 5 Jan 2010 14:05:48 -0800 Subject: Comment thermcopoly1 SNF 2009-12-07 07:42:00: Oil Message-ID: noted From maurice at snf.stanford.edu Tue Jan 5 15:57:26 2010 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Tue, 5 Jan 2010 15:57:26 -0800 Subject: Problem thermcopoly1 SNF 2010-01-05 12:39:06: run fail, door did close Message-ID: ran boat cal From maurice at snf.stanford.edu Wed Jan 6 15:15:49 2010 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Wed, 6 Jan 2010 15:15:49 -0800 Subject: Problem thermcopoly1 SNF 2010-01-05 08:57:09: Needs test Message-ID: Test completep 620poly 00:30:00 expected ~2880 ang actual 2948 - - 2946,2948,2947,2945,2946 From zpatel at snf.stanford.edu Mon Jan 18 15:52:51 2010 From: zpatel at snf.stanford.edu (zpatel at snf.stanford.edu) Date: Mon, 18 Jan 2010 15:52:51 -0800 Subject: Problem thermcopoly1 SNF 2010-01-18 15:52:51: The boat does not close Message-ID: Leak check failed. ran POLYOUT program Reloaded the P580POLY program. Boat start movining in and out half way through and does not reach furnace. Boatstops way before the furnace From maurice at snf.stanford.edu Tue Jan 19 09:52:16 2010 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Tue, 19 Jan 2010 09:52:16 -0800 Subject: Shutdown thermcopoly1 SNF 2010-01-19 09:52:16: heating up after power outage Message-ID: From maurice at snf.stanford.edu Tue Jan 19 15:15:17 2010 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Tue, 19 Jan 2010 15:15:17 -0800 Subject: Shutdown thermcopoly1 SNF 2010-01-19 09:52:16: heating up after power outage Message-ID: temp up From maurice at snf.stanford.edu Tue Jan 19 15:15:38 2010 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Tue, 19 Jan 2010 15:15:38 -0800 Subject: Problem thermcopoly1 SNF 2010-01-18 15:52:51: The boat does not close Message-ID: boat cal'ed From maurice at snf.stanford.edu Tue Jan 19 15:15:45 2010 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Tue, 19 Jan 2010 15:15:45 -0800 Subject: Problem thermcopoly1 SNF 2010-01-19 15:15:44: needs test after power outage Message-ID: From narii at snf.stanford.edu Sat Jan 23 17:01:21 2010 From: narii at snf.stanford.edu (narii at snf.stanford.edu) Date: Sat, 23 Jan 2010 17:01:21 -0800 Subject: Problem thermcopoly1 SNF 2010-01-23 17:01:20: Chamber overheat Message-ID: Never saw this error before, it always shows chamber overheat error. Temperature profile looks good though. From tberg at snf.stanford.edu Tue Jan 26 10:26:22 2010 From: tberg at snf.stanford.edu (tberg at snf.stanford.edu) Date: Tue, 26 Jan 2010 10:26:22 -0800 Subject: Problem thermcopoly1 SNF 2010-01-23 17:01:20: Chamber overheat Message-ID: resolved issue not really a problem From maurice at snf.stanford.edu Tue Jan 26 14:03:26 2010 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Tue, 26 Jan 2010 14:03:26 -0800 Subject: Problem thermcopoly1 SNF 2010-01-19 15:15:44: needs test after power outage Message-ID: King ran P580ph3 00:46:00 PH3=4 expected 700 actual 704 good