From latta at snf.stanford.edu Thu Jul 10 13:29:00 2008 From: latta at snf.stanford.edu (latta at snf.stanford.edu) Date: Thu, 10 Jul 2008 13:29:00 -0700 Subject: Comment tylan3 SNF 2008-07-10 13:28:59: July Process Quals Message-ID: WET900 00:39:00 50 wafer spread Average all wafers = 1028A (expect about 1000A) Within-a-wafer = 0.7% (expect less than 5%) Wafer-to-wafer = 0.7% (expect less than 5%) From latta at snf.stanford.edu Thu Jul 10 13:29:14 2008 From: latta at snf.stanford.edu (latta at snf.stanford.edu) Date: Thu, 10 Jul 2008 13:29:14 -0700 Subject: Comment tylan3 SNF 2008-06-18 14:45:28: June Process Quals Message-ID: new quals posted From mislam at snf.stanford.edu Wed Jul 16 18:57:23 2008 From: mislam at snf.stanford.edu (mislam at snf.stanford.edu) Date: Wed, 16 Jul 2008 18:57:23 -0700 Subject: Problem tylan3 SNF 2008-07-16 18:57:22: MFS Alarm, loader sticking Message-ID: From rshyam at snf.stanford.edu Sun Jul 20 23:43:07 2008 From: rshyam at snf.stanford.edu (rshyam at snf.stanford.edu) Date: Sun, 20 Jul 2008 23:43:07 -0700 Subject: Problem tylan3 SNF 2008-07-20 23:43:06: loader problem again Message-ID: boat did not go in. ericp helped to push it in. From seymour at snf.stanford.edu Mon Jul 21 10:05:17 2008 From: seymour at snf.stanford.edu (seymour at snf.stanford.edu) Date: Mon, 21 Jul 2008 10:05:17 -0700 Subject: Problem tylan3 SNF 2008-07-16 18:57:22: MFS Alarm, loader sticking Message-ID: Loosened drive cable and checked loader movement on rails by hand. It was smooth with no rough spots to cause drag. The loader in auto came out okay, but sputtered when told to go in. Replaced loader drive board and operation on load in was normal. Replaced original board and loader was normal. I suspect a faulty edge card connection that was normalized by removijng and reinserting circuit board. From seymour at snf.stanford.edu Mon Jul 21 10:09:14 2008 From: seymour at snf.stanford.edu (seymour at snf.stanford.edu) Date: Mon, 21 Jul 2008 10:09:14 -0700 Subject: Problem tylan3 SNF 2008-07-21 10:09:13: Loader now functioning correctly Message-ID: I will keep an eye on the loader and exercise it when not in use to verify it continues to operate correctly. From seymour at snf.stanford.edu Tue Jul 22 11:33:12 2008 From: seymour at snf.stanford.edu (seymour at snf.stanford.edu) Date: Tue, 22 Jul 2008 11:33:12 -0700 Subject: Problem tylan3 SNF 2008-07-20 23:43:06: loader problem again Message-ID: No assist required after repair. From seymour at snf.stanford.edu Tue Jul 22 11:36:45 2008 From: seymour at snf.stanford.edu (seymour at snf.stanford.edu) Date: Tue, 22 Jul 2008 11:36:45 -0700 Subject: Problem tylan3 SNF 2008-07-21 10:09:13: Loader now functioning correctly Message-ID: exercised loader in auto three times. Watched complete pulls and pushes and there was no stalls just constant smooth motion. Loader is up.