From till at snf.stanford.edu Thu Jun 4 16:14:14 2009 From: till at snf.stanford.edu (till at snf.stanford.edu) Date: Thu, 4 Jun 2009 16:14:14 -0700 Subject: Problem tylanbpsg SNF 2009-06-04 16:14:14: pin of the nonmetal quartz cover is broken Message-ID: From seymour at snf.stanford.edu Fri Jun 5 15:00:28 2009 From: seymour at snf.stanford.edu (seymour at snf.stanford.edu) Date: Fri, 5 Jun 2009 15:00:28 -0700 Subject: Comment tylanbpsg SNF 2009-06-05 15:00:27: changed pump oil Message-ID: From gth at snf.stanford.edu Sat Jun 6 10:43:38 2009 From: gth at snf.stanford.edu (gth at snf.stanford.edu) Date: Sat, 6 Jun 2009 10:43:38 -0700 Subject: Problem tylanbpsg SNF 2009-06-06 10:43:38: dummies how many ? Message-ID: Dear Maurice A few requests. 1. Please put dummies in all 4 boats. How many do you recommend ? 2. Please put dummies in the casettes in the LTO bins, just in case we need more dummies. 3. Please inform all users how many dummies do you prefer in each boat....someone is running away with the dummies :) thanks for your patience. From gth at snf.stanford.edu Mon Jun 8 00:26:12 2009 From: gth at snf.stanford.edu (gth at snf.stanford.edu) Date: Mon, 8 Jun 2009 00:26:12 -0700 Subject: Problem tylanbpsg SNF 2009-06-08 00:26:11: LTO300PC - large temperature variation Message-ID: I ran LTO300PC the temperature is 300, 310, 312. Please check the recipe. thanks From tura at snf.stanford.edu Tue Jun 9 12:39:12 2009 From: tura at snf.stanford.edu (tura at snf.stanford.edu) Date: Tue, 9 Jun 2009 12:39:12 -0700 Subject: Problem tylanbpsg SNF 2009-06-09 12:39:12: No dummies Message-ID: From seymour at snf.stanford.edu Fri Jun 12 14:45:44 2009 From: seymour at snf.stanford.edu (seymour at snf.stanford.edu) Date: Fri, 12 Jun 2009 14:45:44 -0700 Subject: Comment tylanbpsg SNF 2009-06-12 14:45:44: oil change completed Message-ID: From wanki at snf.stanford.edu Sun Jun 14 16:51:23 2009 From: wanki at snf.stanford.edu (wanki at snf.stanford.edu) Date: Sun, 14 Jun 2009 16:51:23 -0700 Subject: Comment tylanbpsg SNF 2009-06-14 16:51:23: Pump program Message-ID: I think previous user did not successfully run the pump program. From seymour at snf.stanford.edu Mon Jun 15 07:58:43 2009 From: seymour at snf.stanford.edu (seymour at snf.stanford.edu) Date: Mon, 15 Jun 2009 07:58:43 -0700 Subject: Shutdown tylanbpsg SNF 2009-06-15 07:58:42: pump base pressure very high Message-ID: shutting down tube for pump replacement From seymour at snf.stanford.edu Mon Jun 15 12:16:14 2009 From: seymour at snf.stanford.edu (seymour at snf.stanford.edu) Date: Mon, 15 Jun 2009 12:16:14 -0700 Subject: Shutdown tylanbpsg SNF 2009-06-15 07:58:42: pump base pressure very high Message-ID: replaced pump good base of 3 mT leak rate of 10 mT/min needs test after repair From seymour at snf.stanford.edu Mon Jun 15 12:16:37 2009 From: seymour at snf.stanford.edu (seymour at snf.stanford.edu) Date: Mon, 15 Jun 2009 12:16:37 -0700 Subject: Problem tylanbpsg SNF 2009-06-15 00:26:42: Failed Gross Leak Check Message-ID: replaced pump From seymour at snf.stanford.edu Mon Jun 15 12:16:57 2009 From: seymour at snf.stanford.edu (seymour at snf.stanford.edu) Date: Mon, 15 Jun 2009 12:16:57 -0700 Subject: Problem tylanbpsg SNF 2009-06-15 12:16:56: needs test after repair. Message-ID: From seymour at snf.stanford.edu Mon Jun 15 15:51:21 2009 From: seymour at snf.stanford.edu (seymour at snf.stanford.edu) Date: Mon, 15 Jun 2009 15:51:21 -0700 Subject: Comment tylanbpsg SNF 2009-05-15 15:08:14: oil change completed Message-ID: arcived From seymour at snf.stanford.edu Mon Jun 15 15:51:33 2009 From: seymour at snf.stanford.edu (seymour at snf.stanford.edu) Date: Mon, 15 Jun 2009 15:51:33 -0700 Subject: Comment tylanbpsg SNF 2009-04-23 07:40:47: door has had closing issues Message-ID: ok now From seymour at snf.stanford.edu Mon Jun 15 15:51:59 2009 From: seymour at snf.stanford.edu (seymour at snf.stanford.edu) Date: Mon, 15 Jun 2009 15:51:59 -0700 Subject: Comment tylanbpsg SNF 2009-05-22 08:23:49: oil change completed Message-ID: ok now From seymour at snf.stanford.edu Mon Jun 15 15:52:14 2009 From: seymour at snf.stanford.edu (seymour at snf.stanford.edu) Date: Mon, 15 Jun 2009 15:52:14 -0700 Subject: Comment tylanbpsg SNF 2009-06-05 15:00:27: changed pump oil Message-ID: ok From seymour at snf.stanford.edu Mon Jun 15 15:52:24 2009 From: seymour at snf.stanford.edu (seymour at snf.stanford.edu) Date: Mon, 15 Jun 2009 15:52:24 -0700 Subject: Comment tylanbpsg SNF 2009-06-12 14:45:44: oil change completed Message-ID: ok From maurice at snf.stanford.edu Tue Jun 16 09:03:38 2009 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Tue, 16 Jun 2009 09:03:38 -0700 Subject: Problem tylanbpsg SNF 2009-06-15 12:16:56: needs test after repair. Message-ID: Filip's run ran expected. From maurice at snf.stanford.edu Tue Jun 16 09:03:54 2009 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Tue, 16 Jun 2009 09:03:54 -0700 Subject: Comment tylanbpsg SNF 2009-06-14 16:51:23: Pump program Message-ID: pump replaced From maurice at snf.stanford.edu Tue Jun 16 09:10:18 2009 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Tue, 16 Jun 2009 09:10:18 -0700 Subject: Problem tylanbpsg SNF 2009-06-09 12:39:12: No dummies Message-ID: new non metal cleaned and added From maurice at snf.stanford.edu Tue Jun 16 09:11:12 2009 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Tue, 16 Jun 2009 09:11:12 -0700 Subject: Comment tylanbpsg SNF 2009-05-06 02:30:18: Pull out a little bit Message-ID: logged From maurice at snf.stanford.edu Tue Jun 16 09:11:23 2009 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Tue, 16 Jun 2009 09:11:23 -0700 Subject: Comment tylanbpsg SNF 2009-05-12 16:47:19: Is LTO working? Message-ID: yup From maurice at snf.stanford.edu Tue Jun 16 09:11:49 2009 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Tue, 16 Jun 2009 09:11:49 -0700 Subject: Comment tylanbpsg SNF 2009-05-23 12:34:03: Need more nonmetal dummies Message-ID: non metal wafers cleaned and added to box From maurice at snf.stanford.edu Tue Jun 16 09:12:08 2009 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Tue, 16 Jun 2009 09:12:08 -0700 Subject: Comment tylanbpsg SNF 2009-05-28 21:00:47: More Non-metal Dummies Needed Message-ID: more added From maurice at snf.stanford.edu Tue Jun 16 09:12:28 2009 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Tue, 16 Jun 2009 09:12:28 -0700 Subject: Comment tylanbpsg SNF 2009-05-29 16:42:06: dummys are running low (nonmetal) Message-ID: more added From maurice at snf.stanford.edu Tue Jun 16 09:12:45 2009 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Tue, 16 Jun 2009 09:12:45 -0700 Subject: Problem tylanbpsg SNF 2009-06-04 16:14:14: pin of the nonmetal quartz cover is broken Message-ID: boat was replaced From maurice at snf.stanford.edu Tue Jun 16 09:13:27 2009 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Tue, 16 Jun 2009 09:13:27 -0700 Subject: Problem tylanbpsg SNF 2009-05-11 13:04:44: Load End Temperature consistently low Message-ID: old comment...temp cal was done on tube From tura at snf.stanford.edu Tue Jun 16 12:40:32 2009 From: tura at snf.stanford.edu (tura at snf.stanford.edu) Date: Tue, 16 Jun 2009 12:40:32 -0700 Subject: Problem tylanbpsg SNF 2009-06-16 12:40:31: Load side TCU stuck at 57%! Message-ID: I am running LTO400. Load side temperature is 470C and still going up because the TCU is 57.36%. Center and Source side temperatures are about 401C/402C and stable. Something is clearly wrong with temperature stabilization. From seymour at snf.stanford.edu Tue Jun 16 14:00:47 2009 From: seymour at snf.stanford.edu (seymour at snf.stanford.edu) Date: Tue, 16 Jun 2009 14:00:47 -0700 Subject: Comment tylanbpsg SNF 2009-06-16 14:00:47: temp stability issue Message-ID: I checked system, found source high but pump recipe had been loaded and started. I reset the TCU and monitored the zone powers and all looked to be responding normally. I notified Maurice and he will keep an eye on during his run. From maurice at snf.stanford.edu Wed Jun 17 16:55:28 2009 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Wed, 17 Jun 2009 16:55:28 -0700 Subject: Comment tylanbpsg SNF 2009-04-16 18:01:33: Nice film and uniformity so far Message-ID: logged From gth at snf.stanford.edu Wed Jun 17 21:51:10 2009 From: gth at snf.stanford.edu (gth at snf.stanford.edu) Date: Wed, 17 Jun 2009 21:51:10 -0700 Subject: Problem tylanbpsg SNF 2009-06-17 21:51:09: vaccum wand clean non-metal broken. Message-ID: From seymour at snf.stanford.edu Thu Jun 18 08:22:18 2009 From: seymour at snf.stanford.edu (seymour at snf.stanford.edu) Date: Thu, 18 Jun 2009 08:22:18 -0700 Subject: Problem tylanbpsg SNF 2009-06-17 21:51:09: vaccum wand clean non-metal broken. Message-ID: vacuum wand replaced From seymour at snf.stanford.edu Fri Jun 19 14:55:45 2009 From: seymour at snf.stanford.edu (seymour at snf.stanford.edu) Date: Fri, 19 Jun 2009 14:55:45 -0700 Subject: Comment tylanbpsg SNF 2009-06-19 14:55:44: new filter and oil added Message-ID: From narii at snf.stanford.edu Fri Jun 19 23:46:56 2009 From: narii at snf.stanford.edu (narii at snf.stanford.edu) Date: Fri, 19 Jun 2009 23:46:56 -0700 Subject: Problem tylanbpsg SNF 2009-06-19 23:46:55: Lots of peeling Message-ID: Lots of peeling in the tube. From maurice at snf.stanford.edu Fri Jun 26 09:24:23 2009 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Fri, 26 Jun 2009 09:24:23 -0700 Subject: Problem tylanbpsg SNF 2009-06-19 23:46:55: Lots of peeling Message-ID: Checked tube. There is a little peeling but it looks normal. From maurice at snf.stanford.edu Fri Jun 26 09:24:41 2009 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Fri, 26 Jun 2009 09:24:41 -0700 Subject: Comment tylanbpsg SNF 2009-06-16 14:00:47: temp stability issue Message-ID: logged From king at snf.stanford.edu Mon Jun 29 13:08:02 2009 From: king at snf.stanford.edu (king at snf.stanford.edu) Date: Mon, 29 Jun 2009 13:08:02 -0700 Subject: Comment tylanbpsg SNF 2009-06-29 13:08:01: Status of LTO? Message-ID: System is 'yellow-lighted' but the most recent uncleared problem for an old temp stability issue. What is the currrent status, thanks. From maurice at snf.stanford.edu Mon Jun 29 14:36:58 2009 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Mon, 29 Jun 2009 14:36:58 -0700 Subject: Problem tylanbpsg SNF 2009-06-16 12:40:31: Load side TCU stuck at 57%! Message-ID: Ray Reported in a previous coral string: I checked system, found source high but pump recipe had been loaded and started. I reset the TCU and monitored the zone powers and all looked to be responding normally. I notified Maurice and he will keep an eye on during his run. From king at snf.stanford.edu Mon Jun 29 22:04:47 2009 From: king at snf.stanford.edu (king at snf.stanford.edu) Date: Mon, 29 Jun 2009 22:04:47 -0700 Subject: Comment tylanbpsg SNF 2009-06-29 22:04:47: Good LTO400PC results Message-ID: Test run 00:08:00 gave 1089A on each boat, but with random thickness variations. Metal boat back to front, center only: 1069A, 1162, 1056, 1118, 1040. Non-metal boat, center only back to front: 1078A, 1077, 1113. Up to 10% across wafer, using backing wafer in each slot. See lelandstanfordjunior.com for more details. From maurice at snf.stanford.edu Tue Jun 30 10:52:26 2009 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Tue, 30 Jun 2009 10:52:26 -0700 Subject: Comment tylanbpsg SNF 2009-06-30 10:52:26: changed temp stab/LTO300pc Message-ID: Users reported LTO300PC recipe needed more time to stabilze at 300c. -step 65 changed from 6 min to 20 min From maurice at snf.stanford.edu Tue Jun 30 11:35:41 2009 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Tue, 30 Jun 2009 11:35:41 -0700 Subject: Problem tylanbpsg SNF 2009-06-08 00:26:11: LTO300PC - large temperature variation Message-ID: time added to temp stabilization From maurice at snf.stanford.edu Tue Jun 30 11:42:59 2009 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Tue, 30 Jun 2009 11:42:59 -0700 Subject: Comment tylanbpsg SNF 2009-06-30 11:42:58: LTO300 changed Message-ID: Users reported LTO300 recipe needed more time to stabilze at 300c. -step 45 changed from 5 min to 20 min From maurice at snf.stanford.edu Tue Jun 30 11:43:32 2009 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Tue, 30 Jun 2009 11:43:32 -0700 Subject: Comment tylanbpsg SNF 2009-05-23 18:57:59: lto300 recipe Message-ID: -step 45 changed from 5 min to 20 min From maurice at snf.stanford.edu Tue Jun 30 11:45:13 2009 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Tue, 30 Jun 2009 11:45:13 -0700 Subject: Problem tylanbpsg SNF 2009-05-15 18:19:22: Temperature not unform. Message-ID: temp cal'd 5/21/09 this is an old string From maurice at snf.stanford.edu Tue Jun 30 11:46:15 2009 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Tue, 30 Jun 2009 11:46:15 -0700 Subject: Comment tylanbpsg SNF 2009-06-29 13:08:01: Status of LTO? Message-ID: King reports LTO400PC result as good. See her comment for details. From maurice at snf.stanford.edu Tue Jun 30 11:46:50 2009 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Tue, 30 Jun 2009 11:46:50 -0700 Subject: Problem tylanbpsg SNF 2009-06-06 10:43:38: dummies how many ? Message-ID: to be address on wiki