From mdickey at snf.stanford.edu Thu Jun 6 07:06:28 2002 From: mdickey at snf.stanford.edu (mdickey at snf.stanford.edu) Date: Jun 6, 2002 7:06:28 AM Subject: Shutdown tylanpoly 2002-06-06 07:06:27: Pull and clean Message-ID: Tube is down for a pull and clean From mdickey at snf.stanford.edu Thu Jun 6 01:57:31 2002 From: mdickey at snf.stanford.edu (mdickey at snf.stanford.edu) Date: Jun 6, 2002 1:57:31 PM Subject: Shutdown tylanpoly 2002-06-06 07:06:27: Pull and clean Message-ID: Tube is heating up, initial leak check was good. Pull and clean is done From mdickey at snf.stanford.edu Thu Jun 6 01:57:50 2002 From: mdickey at snf.stanford.edu (mdickey at snf.stanford.edu) Date: Jun 6, 2002 1:57:50 PM Subject: Shutdown tylanpoly 2002-06-06 13:57:49: Test Message-ID: Needs test after pull and clean From seymour at snf.stanford.edu Thu Jun 6 02:56:11 2002 From: seymour at snf.stanford.edu (seymour at snf.stanford.edu) Date: Jun 6, 2002 2:56:11 PM Subject: Problem tylanpoly 2002-05-12 22:31:38: tube not moving smoothly Message-ID: replaced loader bearings and checked for proper operation. From gladys at snf.stanford.edu Thu Jun 6 06:30:46 2002 From: gladys at snf.stanford.edu (gladys at snf.stanford.edu) Date: Jun 6, 2002 6:30:46 PM Subject: Shutdown tylanpoly 2002-06-06 18:30:46: tube coating completed: TUBE WON'T MOVE OUT/IN AUTOMATICALLY. Message-ID: From seymour at snf.stanford.edu Fri Jun 7 08:00:51 2002 From: seymour at snf.stanford.edu (seymour at snf.stanford.edu) Date: Jun 7, 2002 8:00:51 AM Subject: Shutdown tylanpoly 2002-06-06 18:30:46: tube coating completed: TUBE WON'T MOVE OUT/IN AUTOMATICALLY. Message-ID: reseated a faulty connection on the loader board to slave computer connector. Tested boat in and boat out in auto and it worked fine. From latta at snf.stanford.edu Fri Jun 7 09:41:30 2002 From: latta at snf.stanford.edu (latta at snf.stanford.edu) Date: Jun 7, 2002 9:41:30 AM Subject: Shutdown tylanpoly 2002-06-06 13:57:49: Test Message-ID: Coat program run. Ok. System back in service. From tberg at snf.stanford.edu Mon Jun 10 06:45:26 2002 From: tberg at snf.stanford.edu (tberg at snf.stanford.edu) Date: Jun 10, 2002 6:45:26 AM Subject: Shutdown tylanpoly 2002-06-10 06:45:25: SiH4 Cylinder Change Message-ID: System down for SiH4 cylinder Change From gladys at snf.stanford.edu Tue Jun 11 03:42:10 2002 From: gladys at snf.stanford.edu (gladys at snf.stanford.edu) Date: Jun 11, 2002 3:42:10 PM Subject: Shutdown tylanpoly 2002-06-10 06:45:25: SiH4 Cylinder Change: testrun completed, ok to use Message-ID: From seymour at snf.stanford.edu Mon Jun 24 08:52:50 2002 From: seymour at snf.stanford.edu (seymour at snf.stanford.edu) Date: Jun 24, 2002 8:52:50 AM Subject: Problem tylanpoly 2002-06-21 11:15:25: small b in temp load . TCU % for load region much higher than other regions Message-ID: Did a system check and a tube status this morning and all was in order. No t/c trouble indications. From sams at snf.stanford.edu Mon Jun 24 03:16:49 2002 From: sams at snf.stanford.edu (sams at snf.stanford.edu) Date: Jun 24, 2002 3:16:49 PM Subject: Problem tylanpoly 2002-06-24 15:16:48: TEMPL shows "b" during process Message-ID: During the process, TEMPL was showing a little b. It was not there at the beginning, and it has gone away now. --Sam From seymour at snf.stanford.edu Tue Jun 25 06:46:41 2002 From: seymour at snf.stanford.edu (seymour at snf.stanford.edu) Date: Jun 25, 2002 6:46:41 AM Subject: Problem tylanpoly 2002-06-24 15:16:48: TEMPL shows "b" during process Message-ID: repaired faulty connection in spike t/c connector