From maurice at snf.stanford.edu Mon Jan 3 16:38:42 2011 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Mon, 3 Jan 2011 16:38:42 -0800 Subject: Comment tylanpoly SNF 2011-01-03 16:38:41: qual test Message-ID: Test complete Ran Polyemit 00:10:00 Expected ~1200 Actual 1146 center From lindaw at snf.stanford.edu Tue Jan 4 12:15:09 2011 From: lindaw at snf.stanford.edu (lindaw at snf.stanford.edu) Date: Tue, 4 Jan 2011 12:15:09 -0800 Subject: Comment tylanpoly SNF 2011-01-04 12:15:08: found vented in polypump program Message-ID: I ran the polypump program after finding the tube vented. I went to vent again about 25 min later, and the tube was vented and in ready mode in polypump program. I will go ahead and try to run amor585 and see what happens. Curious. From lindaw at snf.stanford.edu Tue Jan 4 13:06:02 2011 From: lindaw at snf.stanford.edu (lindaw at snf.stanford.edu) Date: Tue, 4 Jan 2011 13:06:02 -0800 Subject: Problem tylanpoly SNF 2011-01-04 13:06:01: N2BKFL reading 348.9 when set point is 0 Message-ID: During step 60 of amor585, the N2BKFL pressure reading shot up to 348.9, and the process pressure rose to1147.7. the N2BKFL pressure set point is 0, and the process pressure set point for this step is 400. There seems to be a nitrogen leak that is probably why the polypump program keeps self aborting. I aborted my amor585 run at step 60 because the process pressure is too high with the N2 leak. From seymour at snf.stanford.edu Tue Jan 4 15:24:42 2011 From: seymour at snf.stanford.edu (seymour at snf.stanford.edu) Date: Tue, 4 Jan 2011 15:24:42 -0800 Subject: Shutdown tylanpoly SNF 2011-01-04 15:24:42: program keeps ending Message-ID: I have swapped slave cpu and i/o board with no end to problem. From seymour at snf.stanford.edu Wed Jan 5 11:57:13 2011 From: seymour at snf.stanford.edu (seymour at snf.stanford.edu) Date: Wed, 5 Jan 2011 11:57:13 -0800 Subject: Shutdown tylanpoly SNF 2011-01-04 15:24:42: program keeps ending Message-ID: rreplaced op amp and zero pot for n2 purge. this was caussine polypump prc pr to exceed 500 mT and jumping to step 35 (END) From seymour at snf.stanford.edu Wed Jan 5 11:57:53 2011 From: seymour at snf.stanford.edu (seymour at snf.stanford.edu) Date: Wed, 5 Jan 2011 11:57:53 -0800 Subject: Problem tylanpoly SNF 2011-01-04 13:06:01: N2BKFL reading 348.9 when set point is 0 Message-ID: Linda has offered to run a test on the tube. From lindaw at snf.stanford.edu Wed Jan 5 14:37:56 2011 From: lindaw at snf.stanford.edu (lindaw at snf.stanford.edu) Date: Wed, 5 Jan 2011 14:37:56 -0800 Subject: Comment tylanpoly SNF 2011-01-05 14:37:56: AMOR585 test ok target 1500A actual 1515A Message-ID: ran test run AMOR585 24 min. Target thickness 1500A measured thickness 1515 +-16A. From lindaw at snf.stanford.edu Thu Jan 27 12:13:35 2011 From: lindaw at snf.stanford.edu (lindaw at snf.stanford.edu) Date: Thu, 27 Jan 2011 12:13:35 -0800 Subject: Comment tylanpoly SNF 2011-01-27 12:13:35: tylanpoly is missing a dummy wafer Message-ID: The tylanpoly tube has only one dummy wafer. It should have two at the least. Four at the best. From maurice at snf.stanford.edu Thu Jan 27 12:36:33 2011 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Thu, 27 Jan 2011 12:36:33 -0800 Subject: Comment tylanpoly SNF 2010-09-03 13:27:26: ran test run AMOR585 Message-ID: logged From maurice at snf.stanford.edu Thu Jan 27 12:36:39 2011 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Thu, 27 Jan 2011 12:36:39 -0800 Subject: Comment tylanpoly SNF 2010-10-13 09:21:10: oil changed Message-ID: logged From maurice at snf.stanford.edu Thu Jan 27 12:36:52 2011 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Thu, 27 Jan 2011 12:36:52 -0800 Subject: Comment tylanpoly SNF 2010-12-13 14:19:24: tube back together Message-ID: logged From maurice at snf.stanford.edu Thu Jan 27 12:36:59 2011 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Thu, 27 Jan 2011 12:36:59 -0800 Subject: Comment tylanpoly SNF 2010-12-14 06:16:05: Running coat Message-ID: logged From maurice at snf.stanford.edu Thu Jan 27 15:44:38 2011 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Thu, 27 Jan 2011 15:44:38 -0800 Subject: Comment tylanpoly SNF 2011-01-27 12:13:35: tylanpoly is missing a dummy wafer Message-ID: added 4 dummies...there are now 5 in the tube From maurice at snf.stanford.edu Thu Jan 27 15:44:55 2011 From: maurice at snf.stanford.edu (maurice at snf.stanford.edu) Date: Thu, 27 Jan 2011 15:44:55 -0800 Subject: Comment tylanpoly SNF 2011-01-05 14:37:56: AMOR585 test ok target 1500A actual 1515A Message-ID: logged