From ehe at snf.stanford.edu Sat May 17 14:11:32 2008 From: ehe at snf.stanford.edu (ehe at snf.stanford.edu) Date: Sat, 17 May 2008 14:11:32 -0700 Subject: Problem tylansige SNF 2008-05-17 14:11:31: boat needed help loading Message-ID: Boat came out ok, but stopped after a couple seconds of automatic load, had to put it in manual while gently pushing to get it to go the first 5" then motor was able to take over (it was as the boat was sticking at a point) From ehe at snf.stanford.edu Sat May 17 21:36:27 2008 From: ehe at snf.stanford.edu (ehe at snf.stanford.edu) Date: Sat, 17 May 2008 21:36:27 -0700 Subject: Problem tylansige SNF 2008-05-17 21:36:26: motor needs repair Message-ID: Motor is getting worse with each run - requires user to push the boat at times. From tberg at snf.stanford.edu Mon May 19 10:17:08 2008 From: tberg at snf.stanford.edu (tberg at snf.stanford.edu) Date: Mon, 19 May 2008 10:17:08 -0700 Subject: Problem tylansige SNF 2008-05-17 14:11:31: boat needed help loading Message-ID: vented tube, tightened clutch checked in and out OK From tberg at snf.stanford.edu Mon May 19 10:17:18 2008 From: tberg at snf.stanford.edu (tberg at snf.stanford.edu) Date: Mon, 19 May 2008 10:17:18 -0700 Subject: Problem tylansige SNF 2008-05-17 21:36:26: motor needs repair Message-ID: vented tube, tightened clutch checked in and out OK From filip at snf.stanford.edu Sat May 24 16:56:03 2008 From: filip at snf.stanford.edu (filip at snf.stanford.edu) Date: Sat, 24 May 2008 16:56:03 -0700 Subject: Problem tylansige SNF 2008-05-24 16:56:03: coat8 failed leak check 3 times Message-ID: pumps down to 45mT, but during leak check trips the >60mT criterium. Left the tube closed in ready mode. From tberg at snf.stanford.edu Wed May 28 06:02:51 2008 From: tberg at snf.stanford.edu (tberg at snf.stanford.edu) Date: Wed, 28 May 2008 06:02:51 -0700 Subject: Shutdown tylansige SNF 2008-05-28 06:02:50: not pumping Message-ID: From tberg at snf.stanford.edu Wed May 28 09:12:03 2008 From: tberg at snf.stanford.edu (tberg at snf.stanford.edu) Date: Wed, 28 May 2008 09:12:03 -0700 Subject: Shutdown tylansige SNF 2008-05-28 06:02:50: not pumping Message-ID: Added oil to blower checked operation in pump program From tberg at snf.stanford.edu Wed May 28 09:12:14 2008 From: tberg at snf.stanford.edu (tberg at snf.stanford.edu) Date: Wed, 28 May 2008 09:12:14 -0700 Subject: Problem tylansige SNF 2008-05-24 16:56:03: coat8 failed leak check 3 times Message-ID: Added oil to blower checked operation in pump program From munehiro at snf.stanford.edu Thu May 29 18:45:49 2008 From: munehiro at snf.stanford.edu (munehiro at snf.stanford.edu) Date: Thu, 29 May 2008 18:45:49 -0700 Subject: Problem tylansige SNF 2008-05-29 18:45:49: H2 MFC error Message-ID: H2 MFC error. I could not run CHION recipe. From seymour at snf.stanford.edu Fri May 30 07:53:26 2008 From: seymour at snf.stanford.edu (seymour at snf.stanford.edu) Date: Fri, 30 May 2008 07:53:26 -0700 Subject: Comment tylansige SNF 2008-05-30 07:53:25: looking into H2 MFS460 error Message-ID: From seymour at snf.stanford.edu Fri May 30 08:13:34 2008 From: seymour at snf.stanford.edu (seymour at snf.stanford.edu) Date: Fri, 30 May 2008 08:13:34 -0700 Subject: Problem tylansige SNF 2008-05-29 18:45:49: H2 MFC error Message-ID: H2 MFC zero had drifted. I reset the zeros and did an auto zero routine. H2 now flows at setpoint of 100 sccm. Prior to the zero adjust the H2 flowed 128 with a setpoint of 100. From seymour at snf.stanford.edu Fri May 30 08:15:09 2008 From: seymour at snf.stanford.edu (seymour at snf.stanford.edu) Date: Fri, 30 May 2008 08:15:09 -0700 Subject: Comment tylansige SNF 2008-05-30 07:53:25: looking into H2 MFS460 error Message-ID: corrected flow erropr From seymour at snf.stanford.edu Fri May 30 08:15:25 2008 From: seymour at snf.stanford.edu (seymour at snf.stanford.edu) Date: Fri, 30 May 2008 08:15:25 -0700 Subject: Comment tylansige SNF 2008-05-30 08:15:24: H2 flow error corrected. Message-ID: