From bob101 at snf.stanford.edu  Sat Jul 19 01:48:22 2003
From: bob101 at snf.stanford.edu (bob101 at snf.stanford.edu)
Date: Jul 19, 2003 1:48:22 AM
Subject: Problem wafersaw 2003-07-19 01:48:20: Report Problem for wafersaw
Message-ID: <mailman.155.1357938987.26017.wafersaw-pcs@snf.stanford.edu>

ccw erro, index I is not right.



From ychliu at snf.stanford.edu  Sat Jul 19 09:40:16 2003
From: ychliu at snf.stanford.edu (ychliu at snf.stanford.edu)
Date: Jul 19, 2003 9:40:16 PM
Subject: Shutdown wafersaw 2003-07-19 21:40:16: CCW bad
Message-ID: <mailman.156.1357938987.26017.wafersaw-pcs@snf.stanford.edu>




From booth at snf.stanford.edu  Mon Jul 21 09:38:41 2003
From: booth at snf.stanford.edu (booth at snf.stanford.edu)
Date: Jul 21, 2003 9:38:41 AM
Subject: Problem wafersaw 2003-07-19 01:48:20: Report Clear for wafersaw
Message-ID: <mailman.157.1357938987.26017.wafersaw-pcs@snf.stanford.edu>

this fault should have been a shutdown



From booth at snf.stanford.edu  Mon Jul 21 09:39:38 2003
From: booth at snf.stanford.edu (booth at snf.stanford.edu)
Date: Jul 21, 2003 9:39:38 AM
Subject: Shutdown wafersaw 2003-07-19 21:40:16: Report Clear for wafersaw
Message-ID: <mailman.158.1357938987.26017.wafersaw-pcs@snf.stanford.edu>

had to restart system firmware.
Did height & street alignment, Y-offset.
All OK again.



From yyao at snf.stanford.edu  Wed Jul 23 09:23:29 2003
From: yyao at snf.stanford.edu (yyao at snf.stanford.edu)
Date: Jul 23, 2003 9:23:29 AM
Subject: Problem wafersaw 2003-07-23 09:23:28: Report Problem for wafersaw
Message-ID: <mailman.159.1357938987.26017.wafersaw-pcs@snf.stanford.edu>

There was no blade installed when I got on the tool.



From booth at snf.stanford.edu  Wed Jul 23 10:17:05 2003
From: booth at snf.stanford.edu (booth at snf.stanford.edu)
Date: Jul 23, 2003 10:17:05 AM
Subject: Problem wafersaw 2003-07-23 09:23:28: Report Clear for wafersaw
Message-ID: <mailman.160.1357938987.26017.wafersaw-pcs@snf.stanford.edu>

Replaced broken air line fitting.



From sumita at snf.stanford.edu  Thu Jul 24 12:09:48 2003
From: sumita at snf.stanford.edu (sumita at snf.stanford.edu)
Date: Jul 24, 2003 12:09:48 PM
Subject: Problem wafersaw 2003-07-24 12:09:47: Report Problem for wafersaw
Message-ID: <mailman.161.1357938987.26017.wafersaw-pcs@snf.stanford.edu>

Cannot get height-adjustment to work



From mtang at snf.stanford.edu  Thu Jul 24 02:09:51 2003
From: mtang at snf.stanford.edu (mtang at snf.stanford.edu)
Date: Jul 24, 2003 2:09:51 PM
Subject: Problem wafersaw 2003-07-24 12:09:47: Report Clear for wafersaw
Message-ID: <mailman.162.1357938987.26017.wafersaw-pcs@snf.stanford.edu>

The old sticky <enter> button problem on height cal.  Ash is
having no problems now.