From novak at snf.stanford.edu Tue May 2 13:17:54 2006 From: novak at snf.stanford.edu (novak at snf.stanford.edu) Date: Tue, 2 May 2006 13:17:54 -0700 Subject: Comment wbmetal SNF 2006-05-02 13:17:54: PRX-127 Message-ID: I drained the PRX-127 to change the chemical not realizing that we do not have any in stock. It has been ordered but is not in yet. From novak at snf.stanford.edu Tue May 2 13:31:52 2006 From: novak at snf.stanford.edu (novak at snf.stanford.edu) Date: Tue, 2 May 2006 13:31:52 -0700 Subject: Problem wbmetal SNF 2006-05-02 13:31:51: PRX-127 Message-ID: I emptied the PRX-127 and when I went to the chemical cabinet I found that we are out of this chemical. Larry Novak From novak at snf.stanford.edu Tue May 2 13:57:46 2006 From: novak at snf.stanford.edu (novak at snf.stanford.edu) Date: Tue, 2 May 2006 13:57:46 -0700 Subject: Problem wbmetal SNF 2006-05-02 13:57:46: DRAIN FITTING Message-ID: The right side drain fitting has a very slow leak. From latta at snf.stanford.edu Fri May 5 15:32:29 2006 From: latta at snf.stanford.edu (latta at snf.stanford.edu) Date: Fri, 5 May 2006 15:32:29 -0700 Subject: Comment wbmetal SNF 2006-05-02 13:17:54: PRX-127 Message-ID: noted From latta at snf.stanford.edu Fri May 5 15:33:35 2006 From: latta at snf.stanford.edu (latta at snf.stanford.edu) Date: Fri, 5 May 2006 15:33:35 -0700 Subject: Problem wbmetal SNF 2006-05-02 13:31:51: PRX-127 Message-ID: noted From latta at snf.stanford.edu Fri May 5 15:36:43 2006 From: latta at snf.stanford.edu (latta at snf.stanford.edu) Date: Fri, 5 May 2006 15:36:43 -0700 Subject: Problem wbmetal SNF 2006-05-05 15:36:30: Prx127 replaced with PRS1000 Message-ID: The shipment has not arrived, so PRS1000 is now the PR stripper. If you are concerned about plasma etching polymers please use gasonics or drtek2 to remove them before PR strip. From latta at snf.stanford.edu Fri May 5 15:36:45 2006 From: latta at snf.stanford.edu (latta at snf.stanford.edu) Date: Fri, 5 May 2006 15:36:45 -0700 Subject: Problem wbmetal SNF 2006-05-05 15:36:30: Prx127 replaced with PRS1000 Message-ID: The shipment has not arrived, so PRS1000 is now the PR stripper. If you are concerned about plasma etching polymers please use gasonics or drtek2 to remove them before PR strip. From jhaydon at snf.stanford.edu Tue May 9 14:16:34 2006 From: jhaydon at snf.stanford.edu (jhaydon at snf.stanford.edu) Date: Tue, 9 May 2006 14:16:34 -0700 Subject: Comment wbmetal SNF 2006-05-09 14:16:27: dump rinser up grade 5/16 through 5 /17 Message-ID: From jhaydon at snf.stanford.edu Tue May 16 06:42:06 2006 From: jhaydon at snf.stanford.edu (jhaydon at snf.stanford.edu) Date: Tue, 16 May 2006 06:42:06 -0700 Subject: Shutdown wbmetal SNF 2006-05-16 06:42:05: installation of new dump rinsers Message-ID: From uli at snf.stanford.edu Thu May 18 18:07:30 2006 From: uli at snf.stanford.edu (uli at snf.stanford.edu) Date: Thu, 18 May 2006 18:07:30 -0700 Subject: Shutdown wbmetal SNF 2006-05-16 06:42:05: installation of new dump rinsers Message-ID: Upgrades completed, bench decontaminated. AL etch,and both PRS1000 pots are filled up and ready to use. We have two new dump rinsers. Make sure the lids are closed while you use them. From uli at snf.stanford.edu Thu May 18 18:07:47 2006 From: uli at snf.stanford.edu (uli at snf.stanford.edu) Date: Thu, 18 May 2006 18:07:47 -0700 Subject: Comment wbmetal SNF 2006-05-09 14:16:27: dump rinser up grade 5/16 through 5 /17 Message-ID: done From king at snf.stanford.edu Sat May 20 00:11:41 2006 From: king at snf.stanford.edu (king at snf.stanford.edu) Date: Sat, 20 May 2006 00:11:41 -0700 Subject: Problem wbmetal SNF 2006-05-20 00:11:41: The enabled ON light stays off Message-ID: Doesn't indicate being enabled. From king at snf.stanford.edu Sat May 20 00:24:46 2006 From: king at snf.stanford.edu (king at snf.stanford.edu) Date: Sat, 20 May 2006 00:24:46 -0700 Subject: Problem wbmetal SNF 2006-05-20 00:24:45: Out of PRS-1000 Message-ID: Don't drain the hot pots until more comes in. Also, please be careful not to get water spray into these baths from the dump rinsers. From jrjain at snf.stanford.edu Mon May 22 10:21:50 2006 From: jrjain at snf.stanford.edu (jrjain at snf.stanford.edu) Date: Mon, 22 May 2006 10:21:50 -0700 Subject: Shutdown wbmetal SNF 2006-05-22 10:21:49: Liquid Found Around Bench Message-ID: Liquid found on floor around bench and spin-rinse dryer. From jhaydon at snf.stanford.edu Mon May 22 11:47:14 2006 From: jhaydon at snf.stanford.edu (jhaydon at snf.stanford.edu) Date: Mon, 22 May 2006 11:47:14 -0700 Subject: Shutdown wbmetal SNF 2006-05-22 10:21:49: Liquid Found Around Bench Message-ID: leak fixed From jrjain at snf.stanford.edu Mon May 22 14:22:57 2006 From: jrjain at snf.stanford.edu (jrjain at snf.stanford.edu) Date: Mon, 22 May 2006 14:22:57 -0700 Subject: Problem wbmetal SNF 2006-05-22 14:22:55: Random PRS1000 Alarm Message-ID: PRS1000 tank gives sporadic alarms, during which the displayed temperature changes to ~63 C from ~40 C, suggesting that the temperature gauge is failing. I tried changing the upper temp limit to be above the displayed temp, but this did not stop the alarm. From tura at snf.stanford.edu Thu May 25 04:16:34 2006 From: tura at snf.stanford.edu (tura at snf.stanford.edu) Date: Thu, 25 May 2006 04:16:34 -0700 Subject: Comment wbmetal SNF 2006-05-25 04:16:33: alarm goes on when left rinser cover is open Message-ID: i found that the Clean PRS-1000 temperature shoots up and the alarm goes on when i open the left rinser cover.. i dont see how they could be related but this has been true for the last few hours. From latta at snf.stanford.edu Thu May 25 17:11:02 2006 From: latta at snf.stanford.edu (latta at snf.stanford.edu) Date: Thu, 25 May 2006 17:11:02 -0700 Subject: Problem wbmetal SNF 2006-05-20 00:24:45: Out of PRS-1000 Message-ID: noted From latta at snf.stanford.edu Thu May 25 17:11:24 2006 From: latta at snf.stanford.edu (latta at snf.stanford.edu) Date: Thu, 25 May 2006 17:11:24 -0700 Subject: Problem wbmetal SNF 2006-05-20 00:11:41: The enabled ON light stays off Message-ID: coral problem fixed From latta at snf.stanford.edu Thu May 25 17:11:54 2006 From: latta at snf.stanford.edu (latta at snf.stanford.edu) Date: Thu, 25 May 2006 17:11:54 -0700 Subject: Problem wbmetal SNF 2006-05-05 15:36:30: Prx127 replaced with PRS1000 Message-ID: PRX127 here and loaded into bath. From latta at snf.stanford.edu Thu May 25 17:12:20 2006 From: latta at snf.stanford.edu (latta at snf.stanford.edu) Date: Thu, 25 May 2006 17:12:20 -0700 Subject: Problem wbmetal SNF 2006-05-02 13:57:46: DRAIN FITTING Message-ID: fixed during upgrade.... From latta at snf.stanford.edu Thu May 25 17:13:03 2006 From: latta at snf.stanford.edu (latta at snf.stanford.edu) Date: Thu, 25 May 2006 17:13:03 -0700 Subject: Comment wbmetal SNF 2006-05-25 17:13:02: PRX127 is Back and loaded into the bath Message-ID: Please conserve. From jhaydon at snf.stanford.edu Fri May 26 06:42:50 2006 From: jhaydon at snf.stanford.edu (jhaydon at snf.stanford.edu) Date: Fri, 26 May 2006 06:42:50 -0700 Subject: Problem wbmetal SNF 2006-05-22 14:22:55: Random PRS1000 Alarm Message-ID: problem with RTD connector it is ok now